20mm piezo atomizer for ultrasonic fog
Atomizer 20mm Ultrasonic Mist
In Stoc
Piezoelectric element for generating ultrasonic mist from water, ideal for aroma diffusers, humidifiers and DIY projects. It operates at 2.4MHz, offers atomization up to 380 ml/h, has an outer diameter of 20 mm with a gasket and a disc of 16 mm, impedance below 2 ohms for good efficiency. Requires a driver with the right frequency.
Ft586.85
RFID module kit 13.56MHz, RC522, 3.3V
RFID module kit 13.56MHz, RC522 compatible, HW-126, 3.3V
In Stoc
Compatible RC522 RFID module for Arduino projects and other development boards, ideal for reading and writing 13.56MHz cards and key fobs, includes a card and key fob tag plus pins. It operates at 3.3V with low power consumption, supports multiple MIFARE card types, offers fast transfer up to 10Mbit/s, and works reliably between -20 and 80C.
Ft723.69
AD620 voltage amplifier module 3-12VDC
Voltage signal amplifier module, AD620, microvolt, 3-12VDC
In Stoc
Compact solution for amplifying very small signals, useful in measurements and sensors where noise can affect accuracy. Operates at 3-12VDC, adjustable gain 1.5-1000x with adjustable zero, offers low offset and high common mode rejection for clean signal, includes negative voltage output for flexibility in circuits.
Ft1,538.30
Miller tube meter DIY kit, assembled
DIY kit with Miller tube meter, assembled
Last items in stock
Quickly measure gamma and beta radiation with a plug-and-play Geiger-Miller module, ready to use both standalone at 5V or connected to Arduino or other boards for display and logging. It provides audible and LED alarms for immediate notification, sends pulses to a microcontroller or PC for analysis, supports M4011, STS-5, SBM20, J305 tubes and operates with an operating voltage of 330-600V.
Ft38,124.21
10K linear rotary potentiometer module 3-5V
Rotary potentiometer module, 10K, Linear, 3-5V
In Stoc
Ideal for precise analog control in Arduino or other board projects, this module offers continuous adjustment for volume, brightness or speed, using a 10k linear potentiometer with smooth rotation up to 280 degrees. It operates at 3-5V and delivers a voltage on OUT proportional to the position of the shaft, and the 2.54mm pitch and compact dimensions make it easy to integrate on a breadboard.
Ft1,035.94
4-channel 20mm atomizer module USB-C 5V
Atomizer Module, 4 channels 20mm, USB-C, 5V
In Stoc
Atomization module with 4 channels and 20mm piezo discs, generates fine mist for humidifying plants, fountains or DIY projects, simple power supply via USB-C at 5V, offers simultaneous, dynamic or incremental spray modes, uses microporous foil for efficient nebulization and extended coverage.
Ft2,163.73
20mm ultrasonic atomizer module MicroUSB
Ultrasonic atomizer module, 20mm, MicroUSB
In Stoc
Ultrasonic atomizer kit powered by 5V via MicroUSB, ideal for humidification and misting projects in small containers. Includes 20mm piezoelectric disc and sponge stick for constant water supply. Offers dispersion of up to 35 ml/h, low consumption of 2W and silent operation under 36 dB.
Ft753.08
24V ultrasonic fog atomizer kit with LED
Ultrasonic mist atomizer kit with LED, 24V
In Stoc
Submersible ultrasonic cold mist generator, ideal for decorative fountains and ambient effects or as an aroma diffuser. Produces fine mist that disperses quickly, has 12 multi-colored LEDs with automatic change for dynamic lighting, operates at 24VDC with 220VAC power supply, compact construction for easy installation in a water tank.
Ft4,744.40
Arduino compatible sensor starter kit, KY modules
Sensor Starter Kit, Arduino compatible
In Stoc
Complete set of Arduino-compatible sensors and modules, ideal for quick learning and prototyping of electronic projects. Includes motion, vibration, sound, light, temperature and humidity detection, plus switches, joystick, encoder, 5V relay and IR receiver transmitter, for easy testing, quick breadboard integration and practical expansion of DIY and industrial applications.
Ft8,991.96
ToF sensor module VL53L5CX, 8x8 zone with VCSEL laser, I2C
New
ToF Sensor Module VL53L5CX, 8x8 zone, I2C, 3–5 VDC
In Stoc
High-precision VL53L5CX Time-of-Flight sensor with configurable multi-zone detection up to 8x8 (64 zones), measures distance up to 4 meters using an invisible VCSEL laser and operates at frequencies up to 60 Hz. I2C interface, 3 - 5 VDC power supply, compatible with Arduino, ESP32, Raspberry Pi and other platforms, suitable for robotics, environment mapping, obstacle detection and smart systems.
Ft9,819.43
FM radio transmitter module DSP PLL 87 - 108 MHz, 100 mW, with LCD and control buttons
New
FM radio transmitter module, DSP PLL, 87–108 MHz, LCD, campus mode 76–108 MHz
In Stoc
FM radio transmitter module with DSP and PLL technology, with LCD display and 5 buttons, transmits stereo on the 87.0 - 108.0 MHz band or, in campus mode, on the 76.0 - 108.0 MHz band, with an output power of 100 mW. It accepts audio signal from LINE, USB, or the built-in MIC microphone, is powered by 3.0 - 5.0 VDC, and uses a 75 cm antenna. Suitable for wireless microphone, audio broadcasting from a phone or PC, and short-range DIY broadcasting projects.
Ft4,715.93
FM stereo receiver module DSP PLL 87 - 108 MHz with LCD display
New
FM DSP PLL radio receiver module, 87–108 MHz with LCD, Campus mode 76–108 MHz, stereo output 2x3W
In Stoc
FM stereo radio receiver module with DSP and PLL, LCD display and two rotary encoders VOL and FRE for volume and tuning, ideal for active speakers, wireless microphones, school public address systems and DIY projects. It covers the standard 87.0 - 108.0 MHz band, extendable to 76.0 - 108.0 MHz in Campus mode for university stations, with 500 mW stereo audio output on headphones or 2x3 W on speakers, UART serial control and automatic settings memory.
Ft5,888.72
MCP23017 16-bit I2C I/O expander module CJMCU-2317
New
MCP23017 16-bit I2C I/O Expander Module CJMCU-2317
In Stoc
The MCP23017 CJMCU-2317 expander module adds 16 digital input/output pins to a development board via I2C, with a configurable address from A0-A2 for up to 8 modules on the same bus, two interrupt outputs INTA and INTB, internal pull-up on each pin, and compatibility with Arduino, ESP32, STM32 and Raspberry Pi, ideal for relays, LEDs, buttons, and panels with many inputs or outputs.
Ft1,751.37
MCP4725 DAC Module I2C 12-bit with EEPROM and analog output
New
MCP4725 DAC module, I2C, 12-bit, with EEPROM, HW-315
In Stoc
Breakout module with the MCP4725 converter, a 12-bit DAC with I2C interface, which converts a digital value into a real analog voltage on the OUT pin, useful for signal generation, adjustable voltage references, and analog control in projects with Arduino, ESP32, STM32, or Raspberry Pi. It features internal EEPROM memory, an I2C address selectable via the ADDR jumper, and disableable pull-ups for setups with multiple modules on the same bus, with a supply of 2.7 - 5.5 VDC.
Ft879.82
ADS1256 24-bit data acquisition module with STM32F103C8T6
New
ADS1256 24-bit data acquisition module with STM32F103C8T6, 8 channels, RS232, UART
In Stoc
Compact solution for precise measurements of weak analog signals from sensors, load cells or Wheatstone bridges, with 24-bit ADS1256 ADC, up to 30 kSPS and PGA 1-64 for amplification, 8 channels configurable as single-ended or differential, fast data transmission via RS232 DB9 or UART to PC, PLC or development boards, integrated stable 2.5 V reference.
Ft15,572.22
HY-SRF05 ultrasonic sensor 5V, 2-450cm, Arduino compatible
New
Ultrasonic Sensor HY-SRF05, 5 Pins, 2–450 cm, 5V
In Stoc
Ultrasonic module for contactless distance measurement in robots, automation, and Arduino projects, with a range of 2-450 cm and a detection angle of up to 15°. It operates at 5V, uses the TRIG ECHO protocol compatible with HC-SR04, and has 5 pins with OUT for selecting standard mode or single-pin mode. It provides TTL output and good accuracy under ideal conditions. 
Ft959.72
GPS Module NMEA 0183 RS232 1Hz 5V, active antenna IP67
GPS module, NMEA 0183, RS232, 1Hz, 5V
In Stoc
GPS receiver with RS232 output and NMEA 0183 messages, ideal for navigation, monitoring and time synchronization in industrial and maritime systems. It offers 1 Hz update, 66 channels with GPS QZSS support and SBAS corrections for an accuracy of about 2 m, has an active antenna integrated in an IP67 enclosure and is powered at 5 V, with a 2.5 m shielded cable for quick connection.
Ft10,757.10
AC energy measurement module PZEM-004T-100A v3.0, 100A, TTL, 80-260V
New
AC energy measurement module, PZEM-004T-100A, v3.0, 100A, TTL, 80–260V
In Stoc
The module for monitoring consumption on single-phase AC networks, ideal for automation and IoT projects, measures voltage 80-260VAC, current 0-100A with an external transformer, power, frequency, power factor, and energy up to 9999.99kWh, communicates Modbus-RTU via UART TTL 9600, and provides optocoupled isolation for safe integration with Arduino, ESP32, or PC.
Ft6,444.34
100V 300A MOSFET switch module with 5-18V control, direct cooling
New
High-power MOSFET switch module, 100V 300A, 5–18V control
In Stoc
Switch high-power DC loads quickly and directly from a logic or PWM signal, without mechanical relays, supporting up to 100V and 300A peaks. Based on the AOTL66912 MOSFET with very low on-resistance for reduced losses, it is driven at 5–18V, ideally 10–12V at high currents, low-side, on an ultra-compact 14x15mm board.
Ft818.29
XY-MB02YF Bluetooth proximity relay module, 5V relay
Bluetooth proximity switch module, with relay, XY-MB02YF, 5V
In Stoc
Smart proximity switch with Bluetooth BLE, automatically activates a bistable relay when the phone connects and turns off the load after leaving range or disabling Bluetooth. Works without an app, compatible with iOS and Android, has very low power consumption thanks to the latching relay, supports control of up to 10A, and allows advanced settings via AT commands over UART.
Ft5,655.45
Sinilink XY-WFPOW ESP8285 serial to WiFi converter module
Serial-to-WiFi Converter Module, Sinilink, XY-WFPOW, ESP8285H16
In Stoc
Compact WiFi module with ESP8285H16 that adds remote control and real-time monitoring to Sinilink programmable power supplies, mounts directly on the board via a dedicated connector, communicates via 3.3V UART with a ModBUS bridge for commands and telemetry, operates at 3.3-5V with internal regulation, and supports advanced integration through alternative firmware such as ESPHome or Tasmota.
Ft6,342.40
MAX31865 temperature sensor module for PT100, SPI 3-5V
MAX31865 Temperature Sensor Module, PT100 Sensor, 3-5V
In Stoc
Precision converter for temperature measurement with a PT100 sensor, ideal for industrial and laboratory projects, communicates quickly via SPI with microcontrollers such as Arduino or Raspberry Pi. It offers a 15-bit ADC with fine 0.03125°C resolution, accuracy up to ±0.5°C, conversion time of up to 21 ms, and automatic detection of broken cable or short circuit. Power supply 3-5V.
Ft4,357.76
Addressable LED strip WS2812B IP20 10cm 5V RGB
WS2812B addressable LED strip, IP20, 10 cm
In Stoc
Compact solution for RGB lighting effects controlled in DIY and ambient projects, with 6 SMD5050 LEDs per 10 cm, each pixel individually addressable through the integrated WS2812B controller. It operates at 5V and is easily controlled through a single data pin with Arduino, ESP32, or Raspberry Pi. Cut spacing at each LED, IP20 for indoor use.
Ft351.74
Contactless IR touch sensor for LED strip, 5-24V
IR touch sensor, LED strip, contactless detection, 5-24V
In Stoc
You discreetly control LED strips without contact, by touch or by moving your hand 10–20 mm away, with hidden installation behind wood, glass, or plexiglass up to 5 cm, without drilling. It works on 5–24V DC, supports up to 3A, has 4 selectable modes including ON/OFF and continuous dimming, with very low standby consumption and a compact 32x32 mm board.
Ft2,886.50
SIM808 GSM GPRS GPS Bluetooth Module, 5-25V, Arduino compatible
SIM808 development module, GSM-GPRS-GPS-Bluetooth, 5–25V
In Stoc
Development board for communications and localization, ideal for IoT and telemetry projects. It offers quad-band GSM GPRS, precise GPS with fast fix, and Bluetooth, with control via AT commands over UART with autobaud. The UART logic level is selectable at 1.25V, 3.3V, or 5V via VMCU, compatible with Arduino, STM32, ESP32, and Raspberry Pi. Includes GSM and GPS antennas.
Ft10,071.06
DS30P2 PNP NC IR photoelectric sensor module 30cm 6-36V
IR photoelectric sensor module, DS30P2, PNP, NC, 30 cm, 6–36 V
In Stoc
IR photoelectric sensor for proximity detection in industrial applications, operates by diffuse reflection without a reflector, wide 6-36V DC supply for easy integration with PLCs and microcontrollers. It offers a 3-wire PNP NC output, adjustable distance up to 30 cm and fast 2 ms response, M18 housing with IP67 protection and status LED for quick verification.
Ft2,500.78
Xiaozhi AI voice assistant module ESP32-S3 with audio and WiFi
AI Voice Assistant Module, ESP32 S3, Audio, Xiaozhi
In Stoc
Compact solution for projects with AI voice assistant and display, based on a dual-core ESP32-S3 at 240 MHz with 16MB Flash and 8MB PSRAM for fast response. Includes a 1.54" LCD, integrated microphone, and ES8311 audio codec for natural conversations with an external speaker. Offers 2.4 GHz Wi-Fi and Bluetooth 5 LE, and can be easily programmed via USB-C in Arduino IDE, ESP-IDF, or MicroPython.
Ft11,938.15
Analog flex sensor 2.2 inch, compatible with Arduino ESP32
Flex Sensor 2.2 inch, Analog, for robotic glove
In Stoc
2.2 inch flexible analog sensor for measuring bending degree in robotic gloves and wearable projects, changes its resistance from 25K ohm straight to 45K-125K ohm when bent for easy reading with ADC. Durable, over 1 million cycles, operates between -35 and +80°C, 2-pin interface with 0.1 pitch, compatible with Arduino, ESP32, STM32.
Ft10,873.74
GY-BNO055 module, 9-axis orientation sensor, I2C UART, 3-5V
Absolute orientation sensor module, 9 axes, GY-BNO055, IIC, Serial, 3-5V
In Stoc
Compact module for measuring absolute orientation on 9 axes, ideal for robotics, navigation, and wearable devices. It performs sensor fusion directly on-chip for stable and fast data, and includes an accelerometer, gyroscope, and magnetometer with an ARM Cortex-M0+ processor. It operates at 3-5V and communicates easily via I2C or UART, compatible with Arduino, ESP32, STM32, and Raspberry Pi.
Ft7,870.60
7 inch HDMI IPS touchscreen monitor 1024x600 for Raspberry Pi
7-Inch Touchscreen Monitor, Capacitive, HDMI, IPS, 1024x600, Compatible with Raspberry Pi
Last items in stock
Quickly transform a Raspberry Pi or any HDMI source into a control panel, portable terminal, or media center. The 7-inch IPS display with 1024x600 resolution delivers vivid colors and wide viewing angles, while the capacitive touchscreen with up to 5 touch points ensures precise control. Plug and play connection via HDMI and Micro-USB, with stereo speakers and a 3.5 mm jack for audio.
Ft33,072.14
ESP32-S3 AI voice assistant module with 1.54 inch LCD and audio
Out-of-Stock
AI Voice Assistant Module, with ESP32 S3, LCD 1.54inch, Audio
Out-of-Stock
Compact solution for voice assistant projects with display, based on ESP32-S3, offers Wi-Fi and Bluetooth for quick integration into smart home and prototypes, includes ES8311 audio codec with integrated microphone and speaker output, displays the conversation and status on a 1.54-inch color LCD screen, supports switching between AI models such as Qwen, DeepSeek, and Doubao via xiaozhi.me, and is easy to program via USB-C.
Ft11,741.62
GC0308 0.3MP IR camera module USB 5V for Raspberry Pi
IR Camera Module, GC0308, 0.3MP, Plug-and-Play, USB 5V
Last items in stock
Compact IR camera module for clear close-range captures, ideal for IoT applications, access control, or QR scanning. It offers VGA 0.3MP image quality with an 80-degree angle, up to 120 fps for smooth streaming, 850 nm IR LEDs for night vision, and USB 5V plug-and-play UVC connectivity, compatible with Windows, Linux, macOS, Android, and Raspberry Pi.
Ft8,176.43
WiFi Probe Module TZ-DT06, passive MAC sniffer, ESP-M2
WiFi Probe Mode, Passive Sniffer, MAC Addresses, TZ-DT06, ESP M2,5V
In Stoc
Compact module for passive 802.11 sniffing, captures MAC addresses from probe requests for monitoring nearby WiFi devices without network association. Quickly transmits data over UART in hex format with timestamp and CRC, has a FIFO buffer to prevent losses, and an adjustable RSSI threshold for distance filtering. Compatible with 3.3V or 5V, ideal for pedestrian traffic analysis and presence detection.
Ft1,988.31
3.5 inch TFT LCD Display ILI9486 480x320 for Arduino Mega
3.5 inch TFT LCD Display, ILI9486, 480x320, Arduino compatible
In Stoc
The 3.5 inch TFT LCD module for Arduino Mega 2560 offers clear color display for graphical interfaces, menus, and data, with a resolution of 480x320 and 65K colors. The ILI9486 controller accurately renders text and graphics, the 16-bit parallel interface ensures fast refresh, and the integrated 5V to 3.3V logic level conversion allows direct connection. It includes a microSD slot for loading images and content.
Ft9,649.52
BME280 sensor module GY-BME280 3.3V I2C SPI Arduino ESP32
BME280 Sensor Module, Pressure, Temperature, and Humidity, GY-BME280, 3.3V
In Stoc
Precision digital sensor for simultaneous measurement of pressure, temperature, and humidity, ideal for weather stations, environmental monitoring, altimeters, and IoT projects. Operates at 3.3V with very low power consumption, communicates via I2C or SPI for quick integration with Arduino, ESP32, STM32, and Raspberry Pi, offering fine resolution and good stability in readings.
Ft3,780.09
BME280 sensor module 5V GY-BME280 pressure temperature humidity
Out-of-Stock
BME280 Sensor Module, Pressure, Temperature and Humidity, GY-BME280, 5V
Out-of-Stock
High-precision digital sensor for simultaneous measurement of pressure, temperature, and humidity, ideal for weather stations, automation, and IoT projects. The 5V version has an integrated regulator and logic level conversion, allowing direct connection to Arduino without additional circuits and remains compatible with 3.3V platforms. It offers I2C and SPI interfaces, fast response, and good measurement stability.
Ft3,784.69
SIM800C GSM Module USB 5V Quad-band for Arduino ESP32
USB Mode on GSM SIM800C – Quad-band, GPRS, Bluetooth
In Stoc
Compact solution for GSM connectivity in automation and prototyping projects, it allows SMS, voice calls, and GPRS data transfer via AT commands. It connects directly to a PC via 5V USB thanks to the CH340T and appears as a virtual serial port. It works globally on quad band 850 900 1800 1900 MHz, includes Bluetooth and an SMA connector for the antenna, compatible with Arduino, STM32 and ESP32.
Ft5,141.15
AG8 Smart IR Controller ESP32-S3, 8 IR channels, WiFi Ethernet
ESP32-S3 Smart IR Controller, Home Assistant, AG8
Last items in stock
DIN module for automating equipment with remote control, simultaneously controls up to 8 IR devices through independent channels and quickly learns codes with the built-in IR receiver. It integrates automatically into Home Assistant via MQTT, offers stable connectivity via WiFi or Ethernet, and is powered directly at 9-24 VDC, with USB-C for programming and backup.
Ft55,133.71
Inductive sensor M18 LJA18M-10P1 PNP NO 10mm 6-36V
Inductive proximity sensor, PNP, NO, LJA18M-10P1, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects, ideal for industrial automation and DIY projects. Non-flush M18 mounting with a 10 mm detection distance, 6-36 VDC supply, and PNP NO output compatible with PLCs and microcontrollers. Rugged IP67 housing with status LED and integrated 2 m cable for quick connection.
Ft4,180.51
LJA18M-10P2 Inductive Sensor M18 PNP NC 10mm Arduino PLC
Inductive proximity sensor, PNP, NC, LJA18M-10P2, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects in automation and DIY projects. M18 non-flush mounting, detection distance up to 10 mm for iron, PNP NC output compatible with PLCs and controllers, 6–36V DC power supply. Robust housing with IP67 protection, status LED, and integrated 2 m cable for quick installation.
Ft4,180.51
LJA18M-10N1 inductive proximity sensor M18 NPN NO 10mm
Inductive proximity sensor, NPN, NO, LJA18M-10N1, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects, ideal for automation and DIY projects. It mounts quickly on an M18 thread, has an NPN NO output compatible with PLC and Arduino, operates at 6-36 VDC, and offers detection up to 10 mm. Rugged housing with IP67 protection and a status LED for quick verification.
Ft4,180.51
Inductive sensor LJA18M-10N2 M18, NPN NC, 10 mm detection
Inductive proximity sensor, NPN, NC, LJA18M-10N2, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects, ideal for industrial automation and DIY projects. It offers a 10 mm detection distance, NPN normally closed output compatible with PLCs and microcontrollers, 6-36 VDC power supply, and status LED. Robust M18 nickel-plated brass housing and IP67 protection for dusty and humid environments.
Ft4,180.51
GUVA-S12SD UV sensor module 220-370 nm
UV Sensor Module, GUVA-S12SD Photodiode, 3-5V
In Stoc
Compact module for measuring UVA and UVB radiation in the 220–370 nm range, with a linear analog output proportional to the intensity, flexible power supply 3.3–5V, and very low consumption of approximately 0.1 mA. It connects directly to the analog input on Arduino, ESP32, or STM32, making it ideal for weather stations, solar monitoring, and UV protection projects.
Ft902.78
RS485 Soil Sensor 7 in 1 NPKPHCTH-S IP68
7 in 1 Soil Sensor (N, P, K, pH, EC, Moisture, Temperature), RS485, 5–30V
In Stoc
Quickly monitor essential soil parameters for precise fertilization and irrigation, measuring N, P, K, pH, EC, moisture, and temperature in a single device, RS485 Modbus RTU communication for easy integration into SCADA or IoT projects, 316 stainless steel probes and IP68 sealed housing for long-term use, wide 5–30V power supply with low consumption.
Ft33,968.49
Openlog serial data logger microSD
Serial Data Recording Module, microSD, ATmega328, Blackbox, 3-12V
In Stoc
Compact data logging module on microSD card, ideal for sensor logging and Blackbox on drones or embedded systems. Based on ATmega328 at 16 MHz, communicates via UART TTL with configurable speeds from 2400-115200 bps set in CONFIG.TXT, operates at 3-12 V with low power consumption for battery operation, supports cards up to 64GB FAT16/FAT32, and provides status LEDs for writing.
Ft2,120.56
DS1307 RTC clock module I2C 5V
RTC Module DS1307, I2C Interface, 5V
In Stoc
Real-time clock for embedded projects, maintains date and time even without power through backup on CR1220 battery. Communicates simply via I2C at 0x68 using only SDA and SCL, offers full time with automatic correction for months and leap years up to 2100, supports 24h or 12h format with AM PM, and includes 56 bytes of non-volatile RAM for settings.
Ft995.53
QRE1113 IR line sensor module 5V, digital OUT
Line sensor module, QRE1113, IR, 5V
In Stoc
The IR reflective sensor module is ideal for line tracking and black and white contrast detection in robotics projects. It integrates an IR LED and a phototransistor with on-board conditioning for digital output DO, operates at 5V and connects quickly via a 3-pin header. The compact dimensions and mounting hole make it easy to mount, optimal for small distances up to 3 mm.
Ft722.77
WCS1800 Hall current sensor module 35A 5V
Hall Current Sensor Module, WCS1800, AC-DC, 35A, 5V
In Stoc
Hall current sensor for Arduino and 5V systems, measures without breaking the circuit by passing the conductor through the hole. Offers proportional analog output AOUT for bidirectional DC monitoring up to +/-35A and AC up to 25A, plus digital output DOUT with adjustable threshold from potentiometer for overcurrent alarm, with LED indicator.
Ft4,262.25