Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
GPS module, NMEA 0183, RS232, 1Hz, 5V
GPS receiver with RS232 output and NMEA 0183 messages, ideal for navigation, monitoring and time synchronization in industrial and maritime systems. It offers 1 Hz update, 66 channels with GPS QZSS support and SBAS corrections for an accuracy of about 2 m, has an active antenna integrated in an IP67 enclosure and is powered at 5 V, with a 2.5 m shielded cable for quick connection.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
This QUESCAN GPS receiver with RS232 output and 5 VDC power supply (recommended) is a navigation and synchronization solution for industrial and maritime applications. The active antenna is integrated into a waterproof housing, and position data are transmitted as NMEA 0183 messages to a computer, an industrial controller, or other equipment with an RS232 port.
The receiver uses 66 channels and captures GPS and QZSS signals, with SBAS corrections of the WAAS type, offering a horizontal accuracy of approximately 2.0 m CEP with SBAS enabled. Time to first fix is about 31 seconds on a cold start and about 1 second on a warm start. The provided NMEA messages are RMC, GGA, GSA, GSV, GLL, and VTG, with a default update rate of 1 Hz and a tracking sensitivity of -165 dBm.
This version is factory configured to 9600 bps. Connection to the system is made through the 2.5 m shielded cable.
Specifications:
Receiver: GPS / QZSS, with SBAS corrections (WAAS)
Channels: 66
Data interface: RS232
Protocol: NMEA 0183 (RMC, GGA, GSA, GSV, GLL, VTG)
Baud rate: 9600 bps (factory configured)
Update rate: 1 Hz default, 10 Hz max
Horizontal accuracy: 2.0 m CEP (with SBAS)
Speed accuracy: 0.1 m/s
Time accuracy: 1 us synchronized to GPS time
Tracking sensitivity: -165 dBm
Cold start sensitivity: -148 dBm
TTFF (cold start): 31 s
Warm start: 1 s
Maximum altitude: below 50000 m
Maximum speed: below 515 m/s
Maximum acceleration: below 4 G
Flash memory: 4 MB
Supply voltage: 3.3 - 5.0 VDC (typical 5.0 V)
Protection rating: IP67
Cable length: 2.5 m
Operating temperature: -45 ~ +85 °C
Dimensions: 50.5 x 38.5 x 18 mm
Weight: 100 g
Pinout:
Usage:
For proper operation, make sure the antenna has a clear view of the sky, away from obstacles and sources of interference. Connect the receiver to an RS232 port on a PC, an industrial controller, or a communication station, then open a serial terminal configured to 9600 bps, 8 data bits, no parity, and one stop bit (8N1) to read the NMEA messages transmitted by the receiver.
Attention! The RS232 signal level is incompatible with the 3.3 V or 5 V TTL logic level used by microcontrollers. To connect this receiver to an Arduino, ESP32, or Raspberry Pi, an RS232-TTL converter is required (for example, MAX232).
NMEA format:
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
Reviews (1) - Review moderation
Am montat acest modul GPS pe avion la transpondere Funke și Trig, iar instalarea este foarte simplă. Modulul se alimentează la 5 V (cu ajutorul unui modul coborator de la 12 V la 5 V), se conectează la alimentare, iar firul alb (TX – transmisie date) se leagă la pinul de intrare GPS al transponderului. Modulul este prevăzut cu bandă dubluadezivă și se fixează ușor pe bord, într-o zonă cu vizibilitate bună către cer. După instalare, semnalul GPS este recepționat rapid și funcționarea este stabilă. L-am testat în exploatare reală pe aeronave echipate cu transpondere Funke și Trig și îl recomand celor care caută o soluție simplă și accesibilă pentru ADS-B.
