Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
GPS and Compass module, MATEKSYS M10Q-5883, Drone FPV, 5V
Compact module for FPV drones and DIY projects, offers fast and stable positioning with simultaneous GPS, GLONASS, Galileo and BeiDou reception, up to 5Hz update via UBX for better response in flight, integrated QMC5883L compass on I2C for precise orientation, PPS LED easily indicates 3D fix status, includes 15x15 mm patch antenna for easy mounting.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The M10Q-5883 module from MATEKSYS is a compact solution for FPV racing drones, autonomous flight and DIY projects, combining a u-blox SAM-M10Q-00B multi-constellation GNSS receiver with a QMC5883L integrated compass.
You benefit from simultaneous GPS, GLONASS, Galileo and BeiDou reception for faster and more stable positioning, even when the signal is difficult.
Up to 5Hz updating via UBX protocol helps with better flight response, and the PPS LED clearly shows you the module status, solid on when powered on and flashing 1Hz when there is 3D fix.
A 15x15 mm omnidirectional patch antenna completes the package for simple installation and consistent performance, with dedicated UART interfaces for GNSS and I2C for compass.
The GPS works on UART, the QMC5883L compass works on I2C and needs SDA and SCL, it cannot be connected on TX RX to be recognized as a compass. Only the GPS can be used, in this case CL and DA remain free.
Specifications:
Supply voltage: 5 VDC (5V pad/pin)
Consumption: 13 mA (more during initialization)
Manufacturer: MATEK SYS
GNSS receiver: u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo, BeiDou)
Protocol: UBX 5Hz or NMEA 1Hz
PPS LED: Green (steady on when powered on, flashes 1Hz when GNSS has 3D fix)
Compass: Integrated QMC5883L
Interfaces: UART for GNSS, I2C for compass
Operating temperature: -20 ~ 80°C
Antenna type: Patch 15 x 15 mm² with omnidirectional radiation
Antenna size: 15 x 15 x 4 mm
Module size: 20 x 20 x 12.4 mm
Weight: 8g
Connection diagram:
| M10Q-5883 module | Flight Controller |
|---|---|
| 5V | 5V |
| RX | UART_TX GPS |
| TX | UART_RX GPS |
| CL | I2C_SCL COMPASS |
| YES | I2C_SDA COMPASS |
| G | GND |
Use:
Mount the module in a position free from magnetic interference, connect the power and UART/I2C signals. After powering up, calibrate the compass and check the GNSS reception through the flight controller software for accurate flight operation.
Power connection: connect 5V from FC to 5V pad/pin on the module and GND to GND, the module accepts 4-9V DC.
GPS connection on UART: use any free UART on the FC, connections are made crosswise, FC RXx to GPS TX and FC TXx to GPS RX.
Example UART3: FC RX3 to GPS TX and FC TX3 to GPS RX, then enable GPS on UART3 from the Ports menu.
Minimal connection: if FC does not have a free TX you can only bind FC RXx to GPS TX to receive position data, but FC will not be able to automatically configure GPS via UBX.
Important difference: GPS works on UART, the QMC5883L compass works on I2C and needs SDA and SCL, it cannot be connected on TX RX to be recognized as a compass.
Compass on I2C: if the FC has SDA and SCL pads, connect SDA to SDA and SCL to SCL and enable the magnetometer in the firmware, then run the compass calibration.
If the FC does not have SDA and SCL: use the module only as a GPS without a compass, or choose an FC that exposes I2C, or use an external I2C compatible compass.
Betaflight Ports setting: on the chosen UART set GPS to ON.
Betaflight Configuration settings: GPS ON, UBLOX protocol, auto config ON if you have also connected TX to GPS, auto baud ON or usual manual baudrate 57600 or 115200.
Check operation: PPS LED is on solid when powered on, flashes 1Hz when there is a 3D fix, in the interface you should see satellites and coordinates after acquisition.
Package contents:
1x MATEKSYS M10Q-5883 GNSS & Compass
1x Silicone cable JST-GH-6P to JST-GH-6P 200mm
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
