Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
RGB LED strip Driver module, PWM, serial communication 9600bps, 3.3-5V
Easily control common cathode RGB LED strips from Arduino or other boards via serial commands at 9600bps. Provides fine dimming on each RGB channel via PWM, operates with 3.3-5V logic and has 3-way MOSFETs for loads up to 12V strips. Screw connectors for LED and power ensure quick and secure installation.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Module with integrated microcontroller for controlling RGB LED strips via serial communication, compatible with Arduino and other development boards.
This module communicates with the development board via the serial interface at 9600bps and is compatible with logic voltages between 3.3 and 5VDC.
It features screw connectors for connecting the LED strip (4 pins, GND, R, G, B) and its power supply (2 pins, + and -). There are 3-way MOSFETs on the board for individual control of the 3 RGB colors. The LEDs are controlled via PWM (Pulse Width Modulation) to allow dimming of the channels.
On the side are available the power, serial communication and Reset pins. On the VCC and GND pins located next to RX and TX, the module will be powered with the same voltage of the development board and with the common ground (or directly from the power pin of the development board).
The board uses one A1SHB MOSFET for each channel of the RGB strip. It theoretically supports a maximum voltage of 20VDC, therefore being compatible with LED strips up to 12VDC.
Specifications:
Working voltage: 3.3 - 5VDC
Mosfet: A1SHB, SI2301
Maximum LED strip voltage: 12VDC
Dimensions: 37 x 31mm
Communication:
To communicate with the module, data strings composed as follows will be used:
Data (1): Startup, default 0x1F
Data (2): Channel number, 1-Red, 2-Green, 3-Blue
Data (3): channel intensity (0-100%, values correspond to 00-64)
Data (4): checksum, to ensure correct data transmission, represents the sum of the first 3 data.
Example:
The string is composed of the 4 data above according to the example below:
Automatic light setting: 1F 00 00 1F
Red set to 1% intensity: 1F 01 01 21
Red set to 50% intensity: 1F 01 32 52
Red set to 99% intensity: 1F 01 63 83
Green set to 1% intensity: 1F 02 01 22
Green set to 50% intensity: 1F 02 32 53
Green set to 99% intensity: 1F 02 63 84
Blue set to 1% intensity: 1F 03 01 23
Blue set to 50% intensity: 1F 03 32 54
Blue set to 99% intensity: 1F 03 63 85
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
