Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Battery Capacity Tester, ZB2L3, 1-15V
The module for testing the real capacity of batteries between 1 and 15V, by controlled discharge with an external load, displays on the display the voltage, current and mAh consumed during the test, simple 5V power supply via MicroUSB, automatically detects the shutdown voltage or allows manual setting from the buttons, supporting discharge current up to 3A.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The module for testing batteries of any type, which have a voltage between 1 and 15VDC. It uses a load ( the discharge resistor is not always included in the package ) such as a resistor to discharge the battery to the desired voltage, counting the actual capacity of the battery (mAh).
The mode is powered exclusively through the MicroUSB port and at the 5VDC voltage.
The module has an automatic detection function of the discharge voltage, but it can also be set manually from the dedicated buttons.
The integrated display will show the battery voltage, the discharge current and the consumed capacity during the discharge of the battery, in intervals.
DO NOT CONNECT THE BATTERY IN REVERSE! RESPECT THE POLARITY MARKED ON THE PLATE!
Specifications:
Supply voltage: 5VDC
Current consumed in operation: <70mA
Battery voltage supported discharge: 1.2 - 15VDC
Discharge termination voltage: 0.5 - 11VDC
Maximum discharge current supported: 3Ah
Discharge current resolution: 0.001A
Measured voltage error margin: 1%
Measured current error margin: 1.5%
Maximum measured battery capacity: 9999Ah
Compatible: Any battery with voltage between 1 and 15VDC
Dimensions mm: 50 x 37mm
Instructions:
1. Connect the fully charged battery according to the diagram on the PCB. Plus to Plus, Minus to Minus. DO NOT CONNECT IN REVERSE!
2. Connect the load used to discharge the battery according to the image below.
3. Power the tester through the MicroUSB plug with 5VDC.
4. When pressing the OK button, the tester will display the estimated discharge voltage. This value can be adjusted manually using the Plus and Minus buttons.
5. Press OK again and the tester will start discharging the battery with the intermittent display of the three measured parameters (battery voltage, discharge current and discharged capacity).
Errors displayed:
Err1 : Battery voltage higher than 15V
Err2 : Battery voltage lower than the set minimum voltage
Err3 : The battery does not support the discharge current or there is too much resistance on the used wires
Err4 : Current higher than the module limit (3A)
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
Reviews (8) - Review moderation
Comand de foarte multa vreme de la acest magazin , acest produs ar trebui redenumit sau adaugat separat , desi face cam acelasi lucru , este total diferit sunt destul de multe diferente intre modelul ZB2L3 si cel vandut WH-586 acum. ... ZB2L3 se poate calibra , isi seteaza singur tensiunea pana la oprirea testuluit 3V pentru celulele Li-ion 18650 ... WH-586 nu se poate calibra , tensiune minima pana la oprirea testului este de 2,5V nu ma pot pronunta inca in privinta calitati si a rezultatului unui test , inca nu l-am testat
comment Merchant reply
Ne cerem scuze pentru eroare. Am atentionat furnizorul si am corectat aceste informatii in site (vor fi ambele module disponibile separat). Va rugam sa ne contactati pe mail si va vom compensa contravaloarea produsului sub forma de voucher.
Super
Bun produsul
sint bune dar am primit modelu nou dar nu se pot calibra fata de modelu vechi acesta ZB2L3, 1-15V
Foarte multumit i-si face treaba. Expediere foarte rapida, multumesc.
