Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Magnetic encoder module, AS5600, 3.3V, I2C, Analog and Digital
Non-contact module for precise measurement of rotation angle, ideal for motors and automation projects. Operates at 3.3V and offers I2C, analog 0-3.3V and PWM outputs for easy integration with microcontrollers. Includes neodymium magnet and allows setting the direction of rotation via the DIR pin, stable detection at short distances from the magnet.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Magnetic induction angle sensor module, AS5600, non-contact, ideal for precise rotation measurement applications, compatible with a voltage of 3.3VDC.
It features a variety of output modes such as IIC, PWM, and analog voltage, making it suitable for a wide range of projects.
It is normally used in motors to establish the speed of rotation of the shaft, by using the principle of magnetic induction.
The package also includes a permanent neodymium magnet that can be used with the module.
The DIR pin of the module is used to set the direction of rotation, depending on whether it is connected to GND or VCC.
The magnet is detected by the IC at a distance of up to 3mm (or more, depending on the strength of the magnet) but be careful, the magnetic field must be axial, meaning the magnetic field lines must be perpendicular to the sensor.
Specifications:
Supply voltage: 3.3V
Logic voltage: 3.3V (use logic level converter with 5V boards)
Output: PWM, Analog Voltage, IIC
Integrated: AS5600
Measuring distance: 0.5 – 3mm
Mounting type: axial magnetic field
Dimensions mm: 23 x 23mm
Pinout:
Pine | Function | Details |
VCC | feeding | Connects to 3.3V |
GND | Mass | Connects to GND (common ground) |
OUT | Data output | Can operate as PWM or analog voltage (0 - 3.3V) |
DIR | Rotation direction | Definition of the direction of angle increase: GND = increases CW , VCC = decreases CW |
SCL | I2C clock | Clock line for I²C interface |
SDA | I2C data | Data line for I²C interface |
GPO | Mode selection | Internal pull-up ; tied to GND enters programming mode B |
Use:
The module requires a voltage of 3.3V for operation, both logic and power. Do not supply with 5V, this module is only compatible with 3.3VDC! If you use the IIC/I2C interface
Configure the desired output (IIC, PWM or analog voltage) according to the needs of the application, by connecting to the relevant pins.
- For I2C, use the SCL and SDA pins. Use a logic level converter if you are using 5V boards.
AS5600 sensor | Microcontroller (ex: Arduino, ESP32) |
VCC | 3.3V |
GND | GND |
SCL | SCL (ex: A5 on Arduino) |
SDA | SDA (ex: A4 to Arduino) |
OUT | Not connected (not required) |
DIR | GND or VCC (direction setting) |
GPO | OFFLINE |
- For PWM or Analog use the OUT pin
AS5600 sensor | microcontroller |
VCC | 3.3V |
GND | GND |
OUT (Analog or Digital | Digital pin (e.g. D3 Arduino) Analog pin (e.g. A0 Arduino) |
DIR | GND or VCC (direction setting) |
SCL | OFFLINE |
SDA | OFFLINE |
GPO | OFFLINE |
Position the supplied magnet in the measuring axis for correct angle detection.
Set the DIR pin to define the value increase or decrease depending on rotation, by connecting it to GND or VCC, according to the table above. Connected to ground, the value increases clockwise. Connected to VCC, the value decreases clockwise.
Package contents:
1 × AS5600 Magnetic Encoder
1 × Pin header connector
1 × Magnet
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
