Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
MAX31865 Temperature Sensor Module, PT100 Sensor, 3-5V
Precision converter for temperature measurement with a PT100 sensor, ideal for industrial and laboratory projects, communicates quickly via SPI with microcontrollers such as Arduino or Raspberry Pi. It offers a 15-bit ADC with fine 0.03125°C resolution, accuracy up to ±0.5°C, conversion time of up to 21 ms, and automatic detection of broken cable or short circuit. Power supply 3-5V.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The MAX31865 module is a precision RTD-to-digital converter designed for connecting platinum resistance temperature sensors (PT100 or PT1000) to microcontrollers via the SPI interface. Based on the MAX31865 integrated circuit from Analog Devices, the module fully handles sensor excitation, signal amplification, and analog-to-digital conversion, eliminating the need for any additional external circuitry.
It is recommended for industrial applications, measurement laboratories, and any system that requires precision temperature measurements in the -200 ~ 850°C range.
Among its main features are a 15-bit internal ADC with a resolution of 0.03125°C and an accuracy of ±0.5°C, a maximum conversion time of 21 ms, and input protection of up to ±45V against accidental voltages.
The module includes automatic wiring fault detection, signaling both open-circuit and sensor short-circuit conditions. A 430Ω reference resistor is factory-installed on the board, calibrated for PT100 sensors. For use with PT1000 sensors, the reference resistor must be manually replaced with a 4300Ω one before operation.
The module is powered by 3.3 or 5 VDC and is compatible with Arduino, ESP32, STM32, Raspberry Pi, and any other microcontroller or single-board computer with an available SPI interface. The Adafruit MAX31865 library is available for Arduino IDE, ESP-IDF, and MicroPython, simplifying integration into your project.
Specifications:
Chip: MAX31865
Supply voltage: 3.0 - 5.5 VDC
Interface: SPI (CLK, SDO, SDI, CS)
ADC resolution: 15 bits
Temperature resolution: 0.03125°C
Accuracy: ±0.5°C (max)
Conversion time: 21 ms (max)
Measurement range: -200 ~ 850°C
Installed reference resistor: 430Ω (for PT100)
Reference resistor for PT1000: 4300Ω (requires manual replacement)
Input protection: ±45V
Error detection: open circuit, short circuit
Dimensions: 25.6 x 28.3 mm
Layout and pinout:
| Pin | Function |
|---|---|
| VIN | 3.3 or 5 VDC power supply |
| GND | Common ground |
| CLK | SPI Clock |
| SDO | SPI Data Output (MISO) |
| SDI | SPI Data Input (MOSI) |
| CS | SPI Chip Select (active LOW) |
| RDY | Data Ready, optional signal, indicates conversion completion |
| FORCE+ | RTD sensor excitation terminal (+) |
| FORCE- | RTD sensor excitation terminal (-) |
| RTDIN+ | Sensor voltage measurement terminal (+) |
| RTDIN- | Sensor voltage measurement terminal (-) |
Usage:
Connect the PT100 or PT1000 sensor to the module’s RTD terminals (FORCE+, FORCE-, RTDIN+, RTDIN-), following the correct wiring configuration: 2-wire, 3-wire, or 4-wire.
Power the module with 3.3 or 5 VDC through the VIN and GND pins.
Connect the SPI interface to the microcontroller: CLK, SDO (MISO), SDI (MOSI), and CS.
The RDY pin is optional and can be connected to a microcontroller interrupt pin to detect conversion completion without polling.
Install the Adafruit MAX31865 library from the Arduino IDE Library Manager or via pip/idf depending on the platform.
In the code, specify the Rref value corresponding to the sensor used: 430.0 for PT100 or 4300.0 for PT1000.
Specify the sensor’s nominal resistance at 0°C: 100.0 for PT100 or 1000.0 for PT1000.
The library automatically calculates temperature according to the ITS-90 curve, based on the ratio between the sensor resistance and Rref.
Check the module’s error register in your application code to detect possible wiring issues or sensor faults.
Dimensions diagram:
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/max31865.pdf
Package contents:
1 x PT100 sensor
1 x MAX31865 converter module for PT100 / PT1000 sensors
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
