Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
WEMOS D1 Mini Pro ESP8266, WiFi, 16MB, antenna connector
Compact WiFi development board for IoT projects and automation, based on ESP8266, with 16MB flash for complex firmware and OTA updates, ceramic antenna and U.FL connector for external antenna and better coverage, 11 I/O pins plus analog input, CP2104 USB-to-serial interface, and compatibility with Arduino IDE, MicroPython, NodeMCU, and ESPHome.
Shipping by Thursday 22 October
Buying this product earns you 2.00 RON in loyalty points.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The WEMOS D1 Mini Pro board is a compact WiFi development board based on the ESP-8266EX chip, suitable for IoT projects, automation, and wireless applications where space is limited. This version offers 16MB of flash memory, enough for complex firmware, locally stored web pages, and OTA updates, as well as an integrated ceramic antenna together with a U.FL (IPEX) connector for an external antenna, useful when a greater WiFi range is needed.
The board’s main features are an 80 / 160 MHz processor, 2.4GHz 802.11 b/g/n WiFi connectivity, 11 digital I/O pins with support for interrupts, PWM, I2C, and one-wire (except D0), one analog input with a maximum voltage of 3.2V, the CP2104 USB-to-serial converter, and the reset button. All IO pins operate at 3.3V and are not 5V tolerant. I2C communication is available on pins D1 (SCL, GPIO5) and D2 (SDA, GPIO4), while the SPI interface is on pins D5-D8 (SCK, MISO, MOSI, SS). Pin D4 is connected to the board’s built-in LED.
The board is compatible with Arduino IDE, MicroPython, NodeMCU (Lua), and ESPHome, and the D1 mini form factor allows direct mounting of shields from this family (sensors, relays, displays, power modules). Power is supplied through the Micro-USB port or via the 5V pin.
Specifications:
Specifications:
Chip: ESP-8266EX
USB-to-serial converter: CP2104
Flash memory: 16 MB (128 Mbit)
Processor frequency: 80 / 160 MHz
WiFi: 2.4GHz, 802.11 b/g/n
Supply voltage: 5V (Micro-USB or 5V pin)
Operating voltage: 3.3V (IO pins at 3.3V)
Digital pins: 11 (interrupt, PWM, I2C, one-wire, except D0)
Analog input: 1 (maximum 3.2V)
Antenna: integrated ceramic + U.FL/IPEX connector for external antenna
Port: Micro-USB
Compatibility: Arduino IDE, MicroPython, NodeMCU, ESPHome, D1 mini shields
Dimensions: 34.2 x 25.6 mm
Weight: 2.5 g
Layout:
| Pin | Function | ESP-8285 Pin |
|---|---|---|
| TX | TXD | TXD |
| RX | RXD | RXD |
| A0 | Analog input, max. 3.2 V | A0 |
| D0 | I/O | GPIO16 |
| D1 | I/O, SCL | GPIO5 |
| D2 | I/O, SDA | GPIO4 |
| D3 | I/O, 10 kΩ pull-up resistor | GPIO0 |
| D4 | I/O, 10 kΩ pull-up resistor, built-in LED (BUILTIN_LED) | GPIO2 |
| D5 | I/O, SCK | GPIO14 |
| D6 | I/O, MISO | GPIO12 |
| D7 | I/O, MOSI | GPIO13 |
| D8 | I/O, 10 kΩ pull-down resistor, SS (Slave Select) | GPIO15 |
| G | Ground (GND) | GND |
| 5V | 5 V power supply | – |
| 3V3 | 3.3 V power supply | 3.3 V |
| RST | Reset | RST |
Usage:
Install the Silicon Labs CP210x driver if the operating system does not automatically recognize the board.
Connect the board to the computer using a data Micro-USB cable (not just a charging cable).
In Arduino IDE, add the address https://arduino.esp8266.com/stable/package_esp8266com_index.json in Preferences and install the esp8266 package from Boards Manager.
Select the "LOLIN(WEMOS) D1 mini Pro" board, the corresponding COM port, and the 16MB flash size.
Upload the desired program and open Serial Monitor at 115200 baud for verification.
Do not apply voltages higher than 3.3V to the IO pins or higher than 3.2V to pin A0.
Avoid pulling pins D3 and D4 to GND or pin D8 to 3.3V at startup, as these determine the boot mode.
For the external antenna, check the position of the 0-ohm resistor on the board that selects the ceramic antenna or the U.FL connector, connect the antenna, and move the resistor if necessary.
Dimensions diagram:
- Flash memory
- 16 MB
- Wireless connectivity
- WiFi
- Main chip
- ESP8266
- External antenna connector
- Da
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
// WEMOS D1 mini Pro - WiFi scan test
// Built-in LED is on D4 (GPIO2), active LOW
#include <ESP8266WiFi.h>
void setup() {
Serial.begin(115200);
pinMode(LED_BUILTIN, OUTPUT);
digitalWrite(LED_BUILTIN, HIGH); // LED off
WiFi.mode(WIFI_STA);
WiFi.disconnect();
delay(100);
Serial.println();
Serial.println("WEMOS D1 mini Pro - WiFi scan test");
}
void loop() {
digitalWrite(LED_BUILTIN, LOW); // LED on while scanning
Serial.println("Scanning...");
int n = WiFi.scanNetworks();
digitalWrite(LED_BUILTIN, HIGH);
if (n == 0) {
Serial.println("No networks found");
} else {
Serial.printf("%d networks found:\n", n);
for (int i = 0; i < n; i++) {
Serial.printf("%2d: %-32s RSSI: %4d dBm %s\n",
i + 1,
WiFi.SSID(i).c_str(),
WiFi.RSSI(i),
WiFi.encryptionType(i) == ENC_TYPE_NONE ? "open" : "secured");
}
}
WiFi.scanDelete();
Serial.println();
delay(5000);
}
