Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Dust particle sensor, GP2Y1014AU0F, 5V
Sensor for monitoring fine dust, pollen or smoke particles in Arduino projects and other development boards, operates at 5V and has analog output for fast integration, good sensitivity for air quality measurements and stable response, low current with peaks up to 20mA. Comes with cable with connector, 220uF capacitor and 150 ohm resistor for easy connection.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Particle and dust sensor, compatible with Arduino and other development boards, which can be used to detect fine particles of dust, pollen, smoke particles, and so on. It uses a SAHRP sensor and comes with a cable with a connector, a 16V 220uF capacitor and a 150 ohm resistor.
Specifications:
Supply voltage: 5VDC
Operating current: 20mA in peaks
Sensitivity: 0.5V (0.1mg/m3)
Fresh air voltage: 0.9V
Operating temperature: -10 - 65 degrees C
Dimensions mm: 46 x 30 x 17.6mm
Content:
1 x Sensor
1 x Set of wires
1 x Capacitor 16V 220uF
1 x Resistor 150 Ohm
Use:
Resistor 150 Ohm: Connects in series with VLED at 5VDC.
Capacitor 16V 220uF: It is connected to LED GND with the minus and to one end of the resistor with the plus.
Pins:
VLED: It is connected to 5V through the 150Ohm resistor
LED-GND: To GND
LED: On digital pin
S-GND: To GND
Vo: To any analog pin
Vcc: At 5VDC
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
