Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Balance plug 6S, XH2.54 7P, 10cm
6S LiPo battery balance connector, with 7-pin XH2.54 plug and 10cm 22AWG silicone cable, ideal for connecting wires directly to the cells according to the battery configuration. Provides secure connection and compatibility with most balance chargers that use this type of connector, and the flexible wires make it easy to install in tight spaces.
Buying this product earns you Ft24.06 in loyalty points.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The 6S balance connector is a ready-made cable with a 7-pin XH connector and 7 siliconized wires, intended for connecting a lithium battery with 6 cells in series to a balance charger, a monitoring module, or a protection board. The 7 wires carry the voltage of the negative terminal, each cell connection, and the positive terminal, allowing measurement and balancing of the 6 individual cells. It is suitable for LiPo and Li-ion 6S batteries used in RC applications, drones, small electric vehicles, tools, and custom-built battery packs.
The connector is of XH type, with 7 positions in a single row, with the pitch commonly known in commerce as XH2.54. The wires are 22AWG, with flexible silicone insulation, and have a length of 10 cm. The wire ends are stripped and tinned for direct soldering onto the battery pack or protection board. The colors are kept as with standard balance connectors, with one red wire and 6 black wires.
Among the main features are the polarized XH housing with 7 positions, which prevents reverse insertion, the flexible silicone wires, resistant to soldering heat, and the short 10 cm length, useful in compact packs. The connector has no own power supply, since the voltage comes directly from the battery.
The connector is compatible with most balance chargers, adapters, and balance boards that use a 7-pin XH connector for the 6S configuration.
Specifications:
Compatibility: 6S (6 lithium cells in series)
Connector type: XH2.54
Number of pins: 7P
Cable: 22AWG silicone
Number of wires: 7 (1 red, 6 black)
Cable length: 10 cm
Pinout:
| Connector | Pin | Function |
|---|---|---|
| XH 7P connector | 1 | Negative terminal of the pack (cell 1 minus) |
| XH 7P connector | 2 | Cell 1 positive and cell 2 negative |
| XH 7P connector | 3 | Cell 2 positive and cell 3 negative |
| XH 7P connector | 4 | Cell 3 positive and cell 4 negative |
| XH 7P connector | 5 | Cell 4 positive and cell 5 negative |
| XH 7P connector | 6 | Cell 5 positive and cell 6 negative |
| XH 7P connector | 7 | Positive terminal of the pack (cell 6 positive), red wire |
Usage:
Disconnect the battery from any charger or load before working on the wires, and insulate the free ends separately to avoid short circuits between them.
Identify the negative terminal of the pack and connect the black wire from pin 1 of the connector to it, then connect the remaining wires in order to the cell connection points, and the red wire from pin 7 to the positive terminal of the pack.
Observe the polarity and wire order, as incorrect connection may damage the cells, charger, or protection board.
After soldering, check with a multimeter the voltage between the wire from pin 1 and each subsequent wire, and the value should increase in equal steps corresponding to one cell voltage, from approximately 3.0 V to 4.2 V per cell for lithium batteries.
Insulate the solder joints with heat-shrink tubing and avoid stressing the wires at the soldering area.
Connect the connector to the 7-pin balance port of the charger, in the 6S position, taking into account the housing polarity key.
Do not use the balance wires for high charging or discharging currents, as they are intended only for cell measurement and balancing, while the main current passes through the battery power connector.
Do not leave the battery unattended while charging and use a balance charger compatible with the cell type of the pack.
- sway
- Yes
- Number of cells
- 6S
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
