Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Solar charge control module, PWM, RBL-30A, HQ version
PWM controller for solar charging between panel and 12-24V battery, HQ version with better components for increased reliability and lifespan. Offers stable charging up to 30A, LCD display for quick monitoring, 2x USB 5V up to 3A for powering devices, plus programmable light mode for automatic consumer start after sunset.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
PWM solar charging module, with USB output and LCD display, which acts as a charge control between solar panels and battery.
It features a USB port with 5V output that allows charging of USB devices with up to 3A.
This is the HQ (High Quality) version, other lower quality versions are also available at lower prices, which uses quality components, is more reliable and has a longer lifespan compared to the "Low Quality" models.
There are two main methods of charging a battery using a solar panel: the MPPT method and the PWM method.
This is a PWM controller that acts like an electronic switch between the solar panel and the battery as follows:
- The switch is ON when the battery is discharged. The panel transmits all the energy to the battery.
- The switch enters PWM mode (on and off at variable frequency) when the battery is almost charged and maintains the battery voltage at the absorption voltage.
- The switch is OFF when the battery is fully charged, while the battery voltage drops to the floating voltage.
Using a PWM charging module assumes that the maximum voltage of the panel is close to the maximum voltage of the battery. For example, for a 12V battery, with a charging voltage of 14V, a panel that outputs a VMP (maximum voltage) of 18V can be used. MPPT modules, on the other hand, lower the panel voltage to the battery voltage.
It has a programmable light-dependent operating mode, meaning the consumer will only be turned on after sunset when it is dark and the panels do not generate current, with the consumer turned off during the day when the generated energy will only be used to charge the battery.
Specifications:
Model: RBL-30A
Battery voltage: 12 -24VDC
Charging current: 30A maximum
Discharge current: 10A maximum
Maximum power: 360W at 12V, 720W at 24V
Maximum panel voltage: 48V for 24V battery, 24V for 12V battery
Equalization: 14.4V (Sealed Lead Acid), 14.2V (Gel Battery), 14.6V (Unsealed Lead Acid Battery)
Absorption voltage: 13.7V default, adjustable
Discharge stop: 10.7V default, adjustable
Reconnection to charging: 13V
Light mode trigger voltage: 8V panel voltage
USB output: 2x USB-A, 5V, 3A
Module's own current consumption: <10mA
Operating temperature: -35 - +60 degrees C
Display: Monochrome LCD screen
Protections: Short circuit, open circuit, reverse protection, overload protection
Reverse Current Protection: Dual Mosfet
Dimensions mm: 133.5 x 70 x 35mm
Use:
1. Connect the battery to the module, plus to plus, minus to minus.
2. Connect the panel to the module, plus to plus, minus to minus.
3. Connect the consumer to the module, plus to plus, minus to minus.
When disconnecting, the order of disconnecting the consumer, the panel and the battery must be strictly observed. Disconnecting/Connecting in a different order may damage the module.
Menu:
The module has 3 buttons. One MENU that goes through the different settings, one UP button for increasing the value, one DOWN for decreasing the value.
Display:
Below is the information displayed on the LCD display.
Main Settings:
| Parameter | Default value | Adjustable range | Function |
|---|---|---|---|
| Float voltage | 13.7V | 13.3 – 15.0V | Keep the battery fully charged |
| Download link | 12.6V | 11.0 – 13.5V | Reconnect the load after charging. |
| Stop downloading | 10.7V | 9.0 – 12.3V | Protects the battery from deep discharge |
| Load relay | 13.0V | Fixed | Restart battery charging |
| Load equalization | 14.4 / 14.2 / 14.6V | Fixed on battery type | Equalization charge depending on type |
Battery Type:
| Code | Battery Type | Equalization voltage | Float voltage |
|---|---|---|---|
| b01 | Gel | 14.2V | 13.7V |
| b02 | Sealed lead-acid | 14.4V | 13.7V |
| b03 | Liquid lead-acid | 14.6V | 13.7V |
Working Method:
| Set | Description |
|---|---|
| 24H | Permanently active load |
| 0H | Task started from sunset to sunrise (automatic) |
| 1–23H | Task started a fixed number of hours after sunset (timer mode) |
| Manual | Task started/stopped manually from button or menu |
Settings:
| Action | Button / Combination | Result |
|---|---|---|
| Navigation between screens | [MENU] short | Change display (Main → Float → Reconnect → Stop → Work Mode → Battery Type) |
| Entering edit mode | [MENU] long (5 seconds) | The value starts flashing, ready to be changed. |
| Change value | [UP] or [DOWN] | Increases or decreases the displayed value. |
| Save setting and exit | [MENU] long (5 seconds) | Saves the value and returns to normal mode. |
| Reset to default values | [UP] long (5 seconds) in screens 2–5 | Reset to factory settings |
| Manual start/stop of the load | Load key (light bulb button) | Enables or disables the load output |
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
