Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Portable Smoke Extractor Kit, 6015 fan, USB-C, activated carbon filter
Portable DIY fume extractor, ideal for soldering and electronics work, with 3D printed housing, 60mm fan with good airflow and USB-C power supply. It works with 18650 battery via TP4056 for charging and protection, and the voltage booster provides 12V for the fan. The activated carbon filter is removable and fixes the sponge for quick replacement.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Portable smoke extractor kit, using a 3D printed housing, 60mm fan with good airflow, 18650 holder and a charging and power circuit.
The product requires a mandatory 18650 battery because it uses the TP4056 integrated circuit, which handles charging and protecting the battery, and a voltage booster that raises the battery voltage to 12V necessary for the fan to operate.
The filter is removable and has a system that keeps the activated carbon sponge fixed. Given the small size of the filter, to change it it will be necessary to cut out the 55x60mm size from a larger filter.
The product is sold in the following configurations:
DIY KIT configuration:
1x 3D printed case set
1x TP4056 module
1x 12V voltage booster
1x Fan 6015
1x Activated carbon filter
1x 18650 holder
1x KCD11 switch
1x M3 screw set
* 18650 battery NOT INCLUDED
Specifications:
Supply voltage: 5VDC
Consumption: 3W
Charging current: <500mA
Power port: Type-C
Fan voltage: 12VDC
Fan dimensions: 60x60x15mm
Filter: Activated Carbon
Compatible battery: 18650 (not included)
Charging module: TP4056
Color: Gray or Black. Color may vary depending on the batch. Upon request, another color can be shipped if available.
Product dimensions: 89 x 100 x 29mm
Assembly:
Shorten the fan wires to the length needed to solder them to the output of the voltage booster module. The remaining wires will be used to make the connection between the TP4056 module, the voltage booster module and the ON/OFF button.
Insert the KCD11 button into the dedicated socket and solder a wire between the button pin (either of the two) and OUT+ of the TP4056. The second wire is soldered between the remaining free KCD11 button pin and IN+ of the voltage booster module. It is advisable to use heat shrink tubing to insulate the KCD11 switch pins.
Solder the 18650 battery holder wires to the TP4056, Red to B+ and Black to B- . Here too, it is recommended to shorten the wires. The battery holder wires will be redirected through the holes at the base of the holder. Otherwise, due to the limited space, it is possible to cut them when assembling the case.
Solder the fan wires to the output of the voltage booster, Red to OUT+ and Black to OUT- .
Solder the OUT- of the TP4056 module to the IN- of the voltage booster.
The TP4056 module has a dedicated socket in the case (no screws or glue required). Place the fan in the case with the battery holder (with the battery installed) and the voltage booster, push the KCD11 button into the dedicated socket and position the voltage booster in the remaining free space. Route the fan wires through the dedicated cutout (the fan placed with the wires down).
Close the case and (slowly) thread the 6 M3 screws that hold it closed. It is necessary to thread slowly because the screws will create their own thread in the plastic as they thread. If you screw too quickly with a drill or electric screwdriver, the plastic will melt and the screw will spin loose. Maintain pressure between the two halves of the case while threading to keep the case together.
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
