Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Motor driver module, dual H-bridge, DRV8833, 1.5A
Compact dual H-bridge driver based on DRV8833 for controlling one 4-wire stepper motor or two independent DC motors, ideal for Arduino and other development boards. Offers separate PWM control on each channel, 1.5A per motor at 3-10V, overcurrent, short circuit, undervoltage and temperature protection, plus sleep mode for low power consumption.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Motor driver module, compatible with Arduino and other development boards, which uses the integrated DRV8833 which can drive a 4-wire stepper motor or two independent DC motors by using the dual H-bridge, with the help of a PWM signal for each motor separately.
It has protection against current, short circuit, low voltage and temperature. There is also a sleep mode that offers reduced energy consumption.
Specifications:
Supply voltage: 3 - 10VDC
Output current per motor: 1.5A, 2 motors
Dimensions mm: 18.5 x 16mm
Pinouts:
ULT: set to LOW enters sleep mode
OUT1, OUT2: channel 1 H-bridge controlled by IN1 and IN2
OUT3, OUT4: channel 2 H-bridge controlled by IN3 and IN4
EEP PIN: Output protection
VDC: 3-10VDC
GND: GND
Important : Bringing the IN pins of the same channel to the HIGH level together will burn the module!
In order to be able to set the sleep mode, it is necessary to remove the jumper J2. It is possible that it should be short to avoid entering the default sleep mode.
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
