Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Programmable panel delay relay, 12V, with display, T3231
The panel timer module for automation, allows the control of a consumer with delay or cycle, with two times T1 and T2 clearly displayed. It is powered by 12VDC, offers simple programming from buttons and memorization of settings, includes automatic or manual mode with external trigger, powerful relay for switching loads up to 220VAC.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The T3231 relay module is a programmable timer designed for industrial and electronic applications that require precise control of switching times. It can be programmed in multiple configurations, functioning as a timer, delay, cycle, or in manual mode. It features two displays that simultaneously show the two configurable times (T1 shown in red and T2 shown in blue), providing a clear view of the operating parameters.
Configuration is done using the dedicated UP, SET, DOWN, and RESTART buttons, which allow access to the menu and adjustment of values. Times can be set in seconds, minutes, or hours, within a range of 0 to 999, with an error margin of approximately 5%. An important advantage is that the program is retained in memory even if the power supply is interrupted.
The S1 and S0 pins act as an On/Off switch, which means the module has a passive output and must be connected in series with the load. In the off state, the output on S1 and S2 remains open, with no contact. The module also allows control via an external trigger (manual, with program P4=OFF), either by pressing the R button or by connecting an external switch on the PCB. Powered at 12VDC, the module features a 20A relay capable of switching loads up to 220VAC, 10A and a maximum power of 1500W (we recommend long-term use at half of the maximum specifications), making it suitable for a wide range of automation applications.
Warning: The module switches loads powered at 220VAC, a dangerous mains voltage. Connection and handling must be performed only with the power disconnected and by persons familiar with electrical safety rules. Contact with mains voltage can cause electric shock or death.
Specifications:
Supply voltage: 12VDC
Model: T3231
Functions: Timer, Delay, Cycle, Manual
Relay: 20A
Maximum current: 10A
Maximum voltage: 220VAC
Maximum power: 1500W
Dimensions mm: 79 x 26 x 43mm
Panel cutout dimensions: 72 x 40mm
Adjustable times: seconds, minutes, or hours, between 0 - 999
Time error margin: 5%
Functions:
Warning: The module needs 6 seconds to save the settings.
The module retains the program in case of power failure.
| Category | Function Code | Description |
|---|---|---|
| Time unit | P0-0 | Delay in seconds (0 – 999 seconds) |
| P0-1 | Delay in minutes (0 – 999 minutes) | |
| P0-2 | Delay in hours (0 – 999 hours) | |
| Operating mode | P1-0 | The relay activates after delay T1 |
| P1-1 | The relay deactivates after delay T1 | |
| P1-2 | The relay activates after T1, then deactivates after T2 (single sequence) | |
| P1-3 | The relay deactivates after T1, then activates after T2 (single sequence) | |
| P1-4 | The relay activates after T1, then deactivates after T2 (cyclic) | |
| P1-5 | The relay deactivates after T1, then activates after T2 (cyclic) | |
| Trigger mode | P4 = ON | Automatic mode (automatic trigger – default) |
| P4 = OFF | Manual mode (triggered by pressing the "R" button) |
Connection:
Use:
Program setting (P0, P1, P4):
Press and hold SET for about 3-5 seconds.
P0 or P1 appears on the red display.
Briefly press SET to switch between parameters (P0, P1, P4).
Use UP and DOWN to change the selected parameter value.
Wait about 6 seconds for saving.
Setting times T1 and T2:
Briefly press SET.
The red display (T1) flashes and you adjust it with UP or DOWN.
Press SET again.
The blue display (T2) flashes and you adjust it with UP or DOWN.
Press SET again or wait 6 seconds to save.
Manual start:
Enter settings according to the steps above.
Select parameter P4.
Set P4 = OFF.
The output will start only when you press the R (RESTART) button or an external button connected in parallel with it.
Quick configuration examples:
Relay starts after 10 seconds:
P0 = 0 (seconds)
P1 = 0
T1 = 10
Start for 5 seconds then stop:
P0 = 0
P1 = 2
T1 = 0
T2 = 5
Cycle 10 seconds ON / 20 seconds OFF:
P0 = 0
P1 = 4
T1 = 10
T2 = 20
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
Reviews (2) - Review moderation
Este super modulul, livrare ireprosabila. Totusi, lipsesc setarile. Mai jos cate ceva dupa testari: Modul temporizator programabil T3230 *Setari programe: SET lung (>3sec) >> se trece in setari programe: -din SET scurt se selecteaza ciclic P0, P1 (afisaj PV, rosu) -din UP/DOWN se selecteaza subprogramele (afisaj SV, albastru): >Gama de timp pentru P0 :P0.0 (sec.), P0.1 (min), P0.2 (ore), >Tipul de subprogram pentru P1: P1.1, P1.2 etc. *Setare timpi (T1, T2) SET scurt (in repaus sau contorizare): -clipeste PV, se fixeaza T1 din UP/DOWN (valoarea numerica, sec/min/ore din P0), SET scurt din nou: -clipeste SV, se fixeaza T2 din UP/DOWN (similar cu PV) *Obs: -Memorarea setarilor se face in cca 6 sec de inactivitate, -S1, S2 (S0 pe placa) este contactul de releu, NU Pornit/Oprit, -RESTART este pentru pornirea temporizarii. in timpul contorizarii reporneste de la zero. Butonul de RESTART contine 2 contacte NO in paralel Personal am pus un buton extern tip sonerie, in paralel, pentru start temporizare Modulul este versatil, eu il folosesc pentru temporizare ventilator baie.
Totul ok produs transport etc
