Smart servo STS3215 30kg/cm 6-14V TTL
Out-of-Stock
Servo Smart Serial STS3215, 360 degrees, 19kg, 12-bit Encoder, 7.4V
Out-of-Stock
Smart servo for robotics that requires high torque and precise control, operates at 6-8.4V and offers up to 19.5 kg/cm at 7.4V. 12-bit magnetic encoder for fine positioning and real-time feedback, TTL half-duplex serial communication with bus ID for multiple units, metal gears and coreless motor for durability and quick response.
39.06 €
Serial servo driver board UART 9-12.6V
Servo Driver Board, Serial Bus Adapter (A), UART/USB, ST/SC series, Waveshare, 6-12V
In Stoc
Compact board for precise control of ST and SC serial servos in robotics projects, communicates easily with PC or microcontroller via USB Type-C or UART, allows simultaneous control of up to 253 servos on the same bus and real-time feedback reading such as angle, load, and voltage. Operates at 6-12.6 VDC and is powered directly through a 5.5x2.1 mm DC jack.
12.06 €
ESP32-S3 board with 8x8 RGB matrix and QMI8658 IMU
ESP32-S3-Matrix development board, 8x8 RGB matrix, 6-DOF IMU
In Stoc
Compact solution for IoT projects, robotics, and interactive light effects, with ESP32-S3 dual-core 240 MHz and Wi-Fi plus Bluetooth 5 LE Mesh connectivity. It integrates an 8x8 RGB matrix with addressable WS2812 LEDs for animations and displays, a 6-DOF QMI8658 IMU for motion and orientation detection, easy power supply and programming via USB-C, extendable through Dout pin and 17 multifunctional GPIOs.
25.39 €
STM32F103 dev board with Air780E 4G and dual 5V relays
STM32F103 development board, 4G Air780E module, 5V double relay, for IoT
In Stoc
Integrated solution for IoT projects with 4G connectivity and external load control, based on STM32F103 and Air780E LTE Cat.1 bis module with AT firmware and low idle power consumption. Includes two 5V relays controlled from PA4 and PA5, flip-up Nano SIM slot with 4G antenna and network status LED. Simple 5V power supply via USB Type-C or KF128 terminal, easy programming via SWD or USART.
31.05 €
Quectel LC29HDA GNSS RTK module with YEGB000Q1A antenna
Out-of-Stock
GNSS RTK module, dual band, Quectel LC29HDA, with YEGB000Q1A antenna
Out-of-Stock
Professional GNSS RTK solution for stable centimeter-level positioning, ideal for automation, drones, measurements and monitoring in urban environments. Dual band L1 L5 reception with multi-constellation tracking GPS GLONASS Galileo BDS QZSS, high sensitivity with integrated SAW and LNA for interference resistance, UART I2C SPI interfaces and NMEA RTCM support. Includes YEGB000Q1A antenna.
86.13 €
Inductive sensor M18 LJA18M-10P1 PNP NO 10mm 6-36V
Inductive proximity sensor, PNP, NO, LJA18M-10P1, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects, ideal for industrial automation and DIY projects. Non-flush M18 mounting with a 10 mm detection distance, 6-36 VDC supply, and PNP NO output compatible with PLCs and microcontrollers. Rugged IP67 housing with status LED and integrated 2 m cable for quick connection.
10.91 €
Magnetic screw mat 2UUL 155x98mm
Magnetic Carpet, 155x98mm, 2UUL
In Stoc
Magnetic screw mat, ideal for electronics and phone repairs, holds screws and small metal parts to prevent them from getting lost. The surface is graphically divided for quick organization and easy reassembly, wear-resistant black finish, compact size 155x98 mm for small workbenches, magnetic back for attachment to metal surfaces.
6.02 €
QSI-4840 siren module 120dB 6-15VDC
Siren module, 120dB, 6-15VDC
In Stoc
Compact siren for alarm and burglary systems, provides a loud sound warning, audible from a distance, operates at 6-15VDC and offers a level of up to 120dB. Model QSI-4840, emits at 2.8 ± 0.5kHz for a clear signal, consumption 750 mA at 12VDC, dimensions 39 x 47 x 23 mm for easy integration.
3.69 €
UVM-30A UV sensor module 0-1V 3-5V
UV Sensor Module, UVM-30A, Analog 0-1V, 3-5V
In Stoc
Compact sensor for detecting and monitoring UV radiation, ideal for microcontroller projects and portable exposure measurement systems. Covers 200-370 nm, offers 0-1V proportional analog output for easy reading on ADC, operates at 3-5V and has very low consumption, making it suitable for environmental monitoring and educational applications.
14.06 €
Tester module with display and VL53L0X 3.3-5V
Tester Module Set with Display and VL53L0X, 3.3-5V
In Stoc
Compact assembly for fast distance measurement based on ToF, ideal in robots, automation and prototypes. Measures up to 50 cm, displays the value in centimeters directly on the screen, sends data via serial in millimeters, updates automatically every 1 s, operates at 3.3-5V and connects simply via 4 pins.
7.14 €
10K linear rotary potentiometer module 3-5V
Rotary potentiometer module, 10K, Linear, 3-5V
In Stoc
Ideal for precise analog control in Arduino or other board projects, this module offers continuous adjustment for volume, brightness or speed, using a 10k linear potentiometer with smooth rotation up to 280 degrees. It operates at 3-5V and delivers a voltage on OUT proportional to the position of the shaft, and the 2.54mm pitch and compact dimensions make it easy to integrate on a breadboard.
2.70 €
8 LED bar module, common cathode, 3-5V
LED Bar Module, Common Cathode, 8 LEDs, 3-5V
In Stoc
Ideal for visual display and quick testing of digital outputs on Arduino and similar boards, the 8-LED common cathode bar allows individual control of channels with LOW activation. It operates directly at 3-5V thanks to integrated resistors, has low power consumption and different color LEDs for easy signal identification in debugging, status indicators and DIY projects.
2.45 €
JGB37-520 12V 600RPM DC Motor with gearbox
DC motor, JGB37-520, 600RPM, 12V
Last items in stock
DC brush motor with integrated metal gear, ideal for actuators, automation and robots where you need controlled movement at 600 RPM. It operates at 12VDC, delivers stable torque, has efficient transmission and high load durability, with 6 mm shaft for secure mounting and easy compatibility.
8.99 €
DC Motor JGB37-520 12V 7RPM with metal gearbox
DC motor, JGB37-520, 7RPM, 12V
In Stoc
Brushed DC motor with integrated metal gear, ideal for actuators and automations that require slow and controlled movement. Operates at 12V and delivers 7 RPM with stable torque, metal gears provide durability and efficient power transmission. Suitable for robots, small conveyors and industrial projects where reliability matters.
10.34 €
FrSky Dipole T 868MHz Ipex4 Antenna
FrSky Antenna, Dipole T, 868MHz, EU LBT, Ipex4
In Stoc
T-dipole antenna for upgrading FrSky R9 Mini and R9 MM receivers, improves reception and link stability for long range flights. Works in the 868 MHz EU LBT band, offers better coverage through the T-configuration, and the Ipex4 connector ensures secure connection and reduced signal loss. Compact design, easy to integrate on small drones.
12.71 €
BST-113 Electronic Repair Kit 16 pieces
Out-of-Stock
Set of 16 elements for electronics, BST-113
Out-of-Stock
Complete 16-piece kit for maintenance, diagnostics and repairs of electronics and phones, includes VC830L multimeter for precise measurements and 30W letcon for fine soldering. It has flux pump and 0.6 mm flux roller for quick corrections, plus wire strippers, screwdrivers, tweezers and plastic levers for safe interventions.
46.06 €
GA37RG DC Motor with Gearbox 12V 100RPM
DC motor with reducer, GA37RG, 12V, 100RPM
In Stoc
Robust solution for automation, robots and actuators where you need high torque and stable speed. It operates at 12V and delivers 100 RPM output thanks to the precision metal reducer, has a compact 37 mm housing and 6 mm shaft with flat area for secure coupling, low consumption for easy integration into electronic projects.
18.12 €
Ozone generator kit 0.5 g/h with 9W PSU and tube
Ozone Generator Kit, 0.5g/h, 9W, Ozone Tube Source
In Stoc
Compact solution for air purification and water sterilization, delivers up to 0.5 g/h adjustable ozone at only 9 W. Uses corona discharge for efficient conversion and low noise, quartz glass tube with 316L stainless steel electrode for stability and chemical resistance. Works with air or oxygen and has a lifespan of over 20,000 hours.
81.16 €
MATEKSYS M10Q-5883 GPS + Compass module 5V
GPS and Compass module, MATEKSYS M10Q-5883, Drone FPV, 5V
In Stoc
Compact module for FPV drones and DIY projects, offers fast and stable positioning with simultaneous GPS, GLONASS, Galileo and BeiDou reception, up to 5Hz update via UBX for better response in flight, integrated QMC5883L compass on I2C for precise orientation, PPS LED easily indicates 3D fix status, includes 15x15 mm patch antenna for easy mounting.
89.68 €
ENS160 + AHT21 environmental sensor module 5V
Environmental sensor module, ENS160+AHT21, temperature, humidity, VOC, 5V
In Stoc
Compact solution for monitoring indoor air quality, measuring temperature and humidity and detecting VOC for smart home and HVAC automation. It connects quickly to Arduino and other platforms via I2C or SPI, operates at 5V with low consumption of approximately 10mA, offers a wide measurement range and is easy to mount due to its small size.
10.59 €
50mm x 25m Kapton polyimide heat-resistant tape
Kapton tape 25m, 50mm
In Stoc
Kapton tape 25m, 50mm is ideal for PCB masking and protection, electrical insulation and fixing in high temperature areas. The polyimide film with silicone adhesive withstands up to 260 C continuous and 300 C short term, has excellent heat and solvent resistance, minimal shrinkage after baking and removes cleanly.
10.20 €
MICS-5524 VOC air quality sensor module 5V
Air quality sensor module, VOC, MICS-5524, 5V
In Stoc
MICS-5524 sensor module for air quality monitoring and VOC detection, ideal for Arduino projects, automation and industrial applications. Measures total levels of multiple gases such as CO, NO2, H2, NH3 and hydrocarbons, provides easy-to-read analog output on a single pin, operates at 5V and includes Enable pin for heater control and low power consumption.
11.01 €
RF power divider 1-to-2 SMA female 0.5-6GHz
RF Power Divider, 1 to 2, SMA Female, 0.5-6GHz
In Stoc
Quickly splits an RF signal to two devices, ideal for 2.4G WiFi, testing and telecommunications. Covers 0.5-6GHz, offers low loss and stable distribution thanks to microstrip technology, has good isolation between outputs and SMA female connectors for easy integration. The metal housing ensures effective shielding and heat dissipation.
68.88 €
OLED module SH1106 1.3 inch with EC11 rotary encoder and CONFIRM BACK buttons
1.3-inch OLED display module, SH1106, EC11 rotary encoder, I2C
In Stoc
Compact solution for HMI interfaces and DIY projects, it combines a high-contrast 1.3-inch OLED with an EC11 rotary encoder for precise navigation in menus and adjustments. I2C communication reduces wiring and allows quick integration with Arduino and similar boards. It includes encoder push-button and confirm and back buttons for clear control and immediate visual feedback.
7.92 €
INMP441 Digital Microphone Module I2S 24-bit
Digital Microphone Module, Original INMP441, I2S, Omnidirectional, 24-bit, 3.3V
In Stoc
Omnidirectional MEMS microphone with 24-bit I2S output, ideal for ESP32 audio projects without a separate codec. Provides clear voice and ambient capture, with good signal-to-noise ratio and wide frequency response. Operates at 1.8V-3.3V with low consumption, and left/right channel selection is simply done from the L/R pin.
8.80 €
INMP441 I2S 24-bit omnidirectional microphone module
Out-of-Stock
Digital Microphone Module, INMP441 Compatible, I2S, Omnidirectional, 24-bit, 3.3V
Out-of-Stock
Omnidirectional MEMS module with I2S output, ideal for audio projects with ESP32 and other microcontrollers, without a separate codec. Delivers 24-bit data for clear capture of voice and ambient sounds, has good signal-to-noise ratio and low power consumption. Operates at 1.8-3.3V , and left/right channel selection is made simply by the L/R pin.
2.24 €
Stack SpeedyBee F405 V5 with 55A ESC 30x30
Out-of-Stock
FC stack with ESC SpeedyBee, F405 V5, 30x30, OX32, 55A
Out-of-Stock
FPV drone stack with precise control and fast motor response, combining the FC F405 V5 and a 32-bit 4-in-1 55A ESC with OX32 firmware and telemetry. It allows configuration and firmware updates directly from your phone via SpeedyBee Wireless Tuning 2.0, features a built-in 16MB blackbox and barometer, and is compatible with analog and digital FPV systems DJI, Walksnail, and HDZero.
171.30 €
LX-225 Servo Motor 25Kg 240 degree 6-8.4V Arduino
Servomotor Serial Bus, 2 axes, Feedback, Hall Duplex, 25Kg, LX-225, 240 degrees, 6-8.4V
In Stoc
Serial communication servomotor for robotics and automation, ideal for precise movements and heavy-duty tasks. The 2-axis configuration increases mechanical stability in joints and arms, offers extended rotation from 0-240 degrees, torque up to 25Kg/cm, and metal gears with a CNC aluminum housing. Includes real-time feedback for position, voltage, and temperature.
43.81 €
3.5 inch TFT touchscreen SPI 480x320 for Raspberry Pi
3.5 inch touchscreen, Raspberry Pi, 480 x 320, SPI, with ABS case
In Stoc
Compact solution for local interfaces and control panels on Raspberry Pi, with 3.5 inch 480x320 TFT display and 65536 colors, resistive touch control for precise interaction, direct connection to GPIO via SPI without HDMI, ILI9486 and XPT2046 drivers for stable integration. Includes ABS case for protection and clean mounting, plus a stylus.
31.45 €
Power Switch Module with tactile button 3.3-20V 11A
Switch Module, Power Switch, ON-OFF, 3.3-20V, 11A
In Stoc
Electronic ON-OFF switching solution with single-press operation, ideal for quick power control in embedded projects and portable devices. It operates at 3.3-20V and switches up to 11A, has ultra-low standby consumption, compact dimensions of 15x18mm for easy integration, supports simple connection between source and load, and allows for an external button.
3.46 €
GUVA-S12SD UV sensor module 220-370 nm
UV Sensor Module, GUVA-S12SD Photodiode, 3-5V
In Stoc
Compact module for measuring UVA and UVB radiation in the 220–370 nm range, with a linear analog output proportional to the intensity, flexible power supply 3.3–5V, and very low consumption of approximately 0.1 mA. It connects directly to the analog input on Arduino, ESP32, or STM32, making it ideal for weather stations, solar monitoring, and UV protection projects.
2.36 €
LJA18M-10P2 Inductive Sensor M18 PNP NC 10mm Arduino PLC
Inductive proximity sensor, PNP, NC, LJA18M-10P2, 6-36V
In Stoc
Inductive proximity sensor for non-contact detection of metal objects in automation and DIY projects. M18 non-flush mounting, detection distance up to 10 mm for iron, PNP NC output compatible with PLCs and controllers, 6–36V DC power supply. Robust housing with IP67 protection, status LED, and integrated 2 m cable for quick installation.
10.91 €
VS1053B audio module MP3 5V Arduino compatible
Audio Module VS1053B, MP3, 5V
In Stoc
Audio module with VS1053B for Arduino and other boards, plays files from SD card and decodes MP3, OGG, AAC, WMA or MIDI, providing stereo output and headphone output. Also supports real-time OGG recording via built-in microphone or line-in, SPI communication and 5V power supply, ideal for DIY projects, portable players and integrated audio systems.
16.28 €
Breadboard SYB-170 170 tie points blue for prototyping
Breadboard 170 points, SYB-170, Blue
In Stoc
The 170-point test board is ideal for rapid solderless prototyping, 2.54mm pitch for components and DIP circuits, nickel-plated phosphor bronze contacts for stable connections, durable ABS housing, compact dimensions 47x35mm, adhesive tape for mounting, and the ability to connect in series with other boards, compatible with Arduino, ESP32, and STM32.
0.48 €
GPS Module NMEA 0183 RS232 1Hz 5V, active antenna IP67
GPS module, NMEA 0183, RS232, 1Hz, 5V
In Stoc
GPS receiver with RS232 output and NMEA 0183 messages, ideal for navigation, monitoring and time synchronization in industrial and maritime systems. It offers 1 Hz update, 66 channels with GPS QZSS support and SBAS corrections for an accuracy of about 2 m, has an active antenna integrated in an IP67 enclosure and is powered at 5 V, with a 2.5 m shielded cable for quick connection.
28.06 €
Nickel-plated strip 0.15mm 3P for 18650 batteries, 10m
Nickel-plated strip 0.15mm, 20.2mm, 3P, 10 meters
In Stoc
Ideal for making connections in 18650 battery packs in 3P configurations, it allows precise alignment at a distance of 20.2 mm between cells. The 0.15 mm thickness provides a balance between flexibility and strength, the nickel-plated layer improves corrosion protection and contact stability, and the 10 m roll is suitable for assemblies, repairs, or DIY spot welding projects.
31.58 €
Nickel-plated strip 0.15mm 5P for 18650 batteries, 10m
Nickel-plated strip 0.15mm, 20.2mm, 5P, 10 meters
In Stoc
Ideal for making connections in 18650 battery packs, especially 5P configurations, it provides precise spot welds and stable contacts. The 0.15 mm thickness ensures a balance between flexibility and strength, the 20.2 mm pitch makes cell alignment easier, and the nickel-plated layer improves conductivity and corrosion protection. 10 m roll for assembly and repairs.
49.99 €
AC energy measurement module PZEM-004T-100A v3.0, 100A, TTL, 80-260V
New
AC energy measurement module, PZEM-004T-100A, v3.0, 100A, TTL, 80–260V
In Stoc
The module for monitoring consumption on single-phase AC networks, ideal for automation and IoT projects, measures voltage 80-260VAC, current 0-100A with an external transformer, power, frequency, power factor, and energy up to 9999.99kWh, communicates Modbus-RTU via UART TTL 9600, and provides optocoupled isolation for safe integration with Arduino, ESP32, or PC.
16.81 €
100V 300A MOSFET switch module with 5-18V control, direct cooling
New
High-power MOSFET switch module, 100V 300A, 5–18V control
In Stoc
Switch high-power DC loads quickly and directly from a logic or PWM signal, without mechanical relays, supporting up to 100V and 300A peaks. Based on the AOTL66912 MOSFET with very low on-resistance for reduced losses, it is driven at 5–18V, ideally 10–12V at high currents, low-side, on an ultra-compact 14x15mm board.
2.13 €
ADS1256 24-bit data acquisition module with STM32F103C8T6
New
ADS1256 24-bit data acquisition module with STM32F103C8T6, 8 channels, RS232, UART
In Stoc
Compact solution for precise measurements of weak analog signals from sensors, load cells or Wheatstone bridges, with 24-bit ADS1256 ADC, up to 30 kSPS and PGA 1-64 for amplification, 8 channels configurable as single-ended or differential, fast data transmission via RS232 DB9 or UART to PC, PLC or development boards, integrated stable 2.5 V reference.
40.62 €
HY-SRF05 ultrasonic sensor 5V, 2-450cm, Arduino compatible
New
Ultrasonic Sensor HY-SRF05, 5 Pins, 2–450 cm, 5V
In Stoc
Ultrasonic module for contactless distance measurement in robots, automation, and Arduino projects, with a range of 2-450 cm and a detection angle of up to 15°. It operates at 5V, uses the TRIG ECHO protocol compatible with HC-SR04, and has 5 pins with OUT for selecting standard mode or single-pin mode. It provides TTL output and good accuracy under ideal conditions. 
2.50 €
Breadboard 170 points SYB-170 white for Arduino and prototyping
Breadboard, 170 points, SYB-170, White
In Stoc
The 170-point test board is ideal for rapid solderless prototyping, 2.54mm pitch for components and DIP circuits, nickel-plated phosphor bronze contacts for stable connections, durable ABS housing, compact dimensions 47x35mm, adhesive tape for mounting, and the ability to connect in series with other boards, compatible with Arduino, ESP32, and STM32.
0.48 €
Breadboard SYB-170 170 tie-points red for Arduino and prototyping
Breadboard, 170 points, SYB-170, Red
In Stoc
The 170-point test board is ideal for rapid solderless prototyping, 2.54mm pitch for components and DIP circuits, nickel-plated phosphor bronze contacts for stable connections, durable ABS housing, compact dimensions 47x35mm, adhesive tape for mounting, and the ability to connect in series with other boards, compatible with Arduino, ESP32, and STM32.
0.48 €
Breadboard SYB-170 170 tie points green for prototyping
Breadboard, 170 points, SYB-170, Green
In Stoc
The 170-point test board is ideal for rapid solderless prototyping, 2.54mm pitch for components and DIP circuits, nickel-plated phosphor bronze contacts for stable connections, durable ABS housing, compact dimensions 47x35mm, adhesive tape for mounting, and the ability to connect in series with other boards, compatible with Arduino, ESP32, and STM32.
0.48 €
Breadboard SYB-170 170 points black for Arduino
Breadboard, 170 points, SYB-170, Black
In Stoc
The 170-point test board is ideal for rapid solderless prototyping, 2.54mm pitch for components and DIP circuits, nickel-plated phosphor bronze contacts for stable connections, durable ABS housing, compact dimensions 47x35mm, adhesive tape for mounting, and the ability to connect in series with other boards, compatible with Arduino, ESP32, and STM32.
0.48 €
Waveshare Zero Mini RP2350A development board USB Type-C
Waveshare Zero Mini Development Board, RP2350
In Stoc
The ultra-compact development board for projects where space matters can be soldered directly onto a PCB thanks to its castellated edges. It includes the RP2350A with a choice between Arm Cortex-M33 or RISC-V up to 150 MHz, 4 MB Flash and 520 KB SRAM, 29 GPIO with SPI, I2C, UART, ADC, PWM, and PIO for custom protocols. Simple programming via USB Type-C, plus an integrated WS2812 RGB LED.
14.56 €
WEMOS D1 Mini Pro ESP8266 WiFi development board 16MB with antenna connector
New
WEMOS D1 Mini Pro ESP8266, WiFi, 16MB, antenna connector
In Stoc
Compact WiFi development board for IoT projects and automation, based on ESP8266, with 16MB flash for complex firmware and OTA updates, ceramic antenna and U.FL connector for external antenna and better coverage, 11 I/O pins plus analog input, CP2104 USB-to-serial interface, and compatibility with Arduino IDE, MicroPython, NodeMCU, and ESPHome.
7.90 €
MCP23017 16-bit I2C I/O expander module CJMCU-2317
New
MCP23017 16-bit I2C I/O Expander Module CJMCU-2317
In Stoc
The MCP23017 CJMCU-2317 expander module adds 16 digital input/output pins to a development board via I2C, with a configurable address from A0-A2 for up to 8 modules on the same bus, two interrupt outputs INTA and INTB, internal pull-up on each pin, and compatibility with Arduino, ESP32, STM32 and Raspberry Pi, ideal for relays, LEDs, buttons, and panels with many inputs or outputs.
4.57 €