Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
BMS Li-Ion module, 14S, 45A, with balance, 52V
Passive balance BMS board for 14S Li-Ion packs at 52V, ideal for protecting and maintaining cell balance during charging. Supports 45A continuous and short peaks up to 150A, includes protections against overcharge, overdischarge, short circuit and overcurrent. 15-pin balance plug and cables are included, resistors on the heatsink ensure better cooling.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
BMS (Battery Management System) protective board with balancing (balance), compatible with Lithium Ion cells with a maximum voltage of 4.2V in a charged state, designed to provide safety and efficiency to battery systems with a configuration of 14 cells in series (14S ), operating at a voltage of 52V.
It has protection and balancing features, being ideal for managing and maintaining the optimized performance of battery packs in a variety of applications. The Balance function of the module compensates for the small voltage differences that may appear between the inserted cells, in their daily use. The balance is a passive one, in the sense that on each battery series there is a resistor that, by generating heat, will discharge from the series of cells that have a higher voltage compared to the other lines of inserted batteries. The discharge of these cells is done with a fairly small current (approximately 42mA), only during the charging process (toward the completion of charging at 4.2V). This small balancing current is sufficient if the cells used are identical to the specifications, but if cells with different characteristics or levels of wear are used, it will not be able to compensate for the voltage differences.
The BMS can support a continuous current of up to 45A, with short peaks of up to 150A, specifications that make it suitable for a multitude of projects.
It has multiple protections such as short-circuit protection, low-voltage and high-voltage protection on each individual series, over-current protection.
The balance plug is included, with wires ready to solder to the cell pack terminals.
The balancing resistors are placed on the heatsink (they are not on the main PCB) and connect to the main board via a pin header. This ensures a more compact size of the BMS but also an improved cooling, considering the fact that the resistors will heat up trying to keep the cells in balance with each other.
Specifications:
Maximum package voltage: 58.8VDC
Nominal voltage Package: 52VDC
Type: BMS
Configuration: 14S
Continuous Discharge Current: 45A
Instantaneous Discharge Current: 150A
Charging Voltage: 58.8VDC
Charge-Discharge Current: 45A
Overvoltage Protection: 4.25V (±0.025V)
Response time: 100ms
Reset voltage: 4.05V (±0.05V)
Over Discharge Protection: 2.8V (±0.08V)
Response time: 100ms
Reset voltage: 3.0V (±0.1V)
Overcurrent Protection: 180A (±20A)
Response time: 10ms
Overcurrent reset: Disconnect the load
Short Circuit Protection: Yes
Response time: 200µs.
Reset Short Circuit: Disconnect Negative
Balance Voltage: 4.2V (±0.025V)
Balanced current: 42±5
Balance Type: Passive
Internal Resistance: ≤15mΩ
Own Consumption: ≤40µA, ≤10µA in sleep mode (when the battery is over-discharged)
Balanced socket: 15 pins, with cables
Dimensions: 120 x 60 x 8mm
Use:
Before connecting the plug to the BMS, solder the wires on the batteries starting from 0V (BLACK wire) , followed by the next Red wire to the Plus of the first battery (4.2V) , followed by the Plus of the next battery, until the connections are completed where you should have the last Red wire to the Final Plus of the battery pack. Once you've made sure you've connected the batteries to the plug, CHECK again to make sure it's connected properly.
Afterwards, connect the plug to the BMS and make the connections with the power wires. In the case of this BMS, the SAME PORT type connection is used, that is, the same terminals are used for both charging and discharging. In the picture below, the rectangle with + and - (a plug in this case) is used for both charging and discharging. Only the minus of the package passes through the BMS, the plus goes directly to the consumer/charger.
- Technology
- Lithium Ion
- Load voltage
- sway
- Yes
- Nominal Current
- Number of cells
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
