Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
PD and QC trigger module, 5V, 9V, 12V, 15V, 20V, adjustable, 100W, 5A, USB Type-C, with terminal
USB Type-C trigger board for testing and simulating PD and QC fast charging, useful in diagnosing compatible sources and devices. Select the voltage from the button 5V, 9V, 12V, 15V or 20V, delivers up to 100W, 5A on screw terminals, LEDs indicate voltage and compatibility, remembers the last setting when recharging.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Trigger mode designed to test and simulate the Quick Charge and Power Delivery (PD) protocol on USB Type-C ports. This device provides a convenient solution for testing and analyzing fast charging functionality and charging protocol detection on devices with a USB Type-C port. It supports up to 100W and the voltage is supplied on the screw connector.
The integrated button changes the protocol and the voltage requested by the module. The module will only output voltages and power supported by the used source.
It has integrated LEDs that indicate the output voltage. When selecting the voltage, if the LED is fixed on the voltage set in the button, this voltage is found on the output. If the LED flashes on the set voltage, it means that the charger does not support the respective voltage.
It has a memory, that is, once set, when recharging, the module will maintain the last set voltage.
The Trigger Board is compatible with QC 2.0, QC 3.0, PD 2.0 and PD 3.0 protocols, allowing the testing and simulation of various fast charging modes for devices with a USB Type-C port.
Specifications:
Supply voltage: 5 - 20VDC
USB plug: Type-C
Output power: MAX 100W
Maximum output current: 5A at 20V
Support protocols: PD3.0, PD2.0, QC, FCP, AFC
Supported voltages: 5V/9V/12V/20V
Dimensions mm: 44 x 18mm
Use:
On the back of the module there are a series of contacts that can be shorted to set the function.
PD ONLY: After short-circuiting, it will only work in PD mode.
DM and DP: They are Data- and Data+. We do not recommend short-circuiting these contacts unless you know what you are doing.
5V/9V/12V/20V: Fixed voltage selectors (only if the charger is compatible).
S1: The button acts as an ON/OFF switch.
F1: The lowest available voltage is activated.
F2: The highest available voltage is activated.
F1+F2: The module cycles the available tennis positions as long as the contacts F1 and F2 are shorted.
Setting the polling time or the voltage jump time when F1 and F2 are short-circuited: press and hold the button without turning on the power, then the first LED will flash. If you release the button, it will be unlocked. Otherwise, keep pressing and holding until all LEDs flash, then release the button to enter the time setting, and the switching time is reset to 0.5 seconds. At this moment, 0.5 seconds will be added for each button press, and the LED will display the corresponding time in binary mode (you can count how many times you have added the time if you are not familiar with binary), up to 30 times (the maximum corresponding time is 15.5 seconds, and the LEDs are all lit).
If the button is not pressed within 3 seconds, the time setting will appear automatically and the set value will be saved, and the LEDs will flash intensely to warn.
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
