Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Frequency to Voltage converter module, 0-1KHz to 0-10V, 13.5-30V
Converts a 0-1 kHz pulse signal into a proportional 0-10V analog voltage, ideal for pulse sensors, encoders and PLC interfacing. It operates at 13.5-30V, has an optically isolated input for protection and immunity to interference, and the output is easily calibrated from the potentiometer for exact matching to the application.
Shipping by Thursday 27 August
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
Frequency to Voltage conversion module that converts a pulse signal into analog voltage, so that the input frequency is converted into a proportional 0-10V level.
It operates on 13.5V-30V power supply and accepts input frequencies between 0 and 1 kHz, making it suitable for interfacing with pulse sensors, encoders or digital outputs.
The output voltage is adjustable by potentiometer, allowing fine calibration of the frequency-voltage relationship depending on the application. The input is made with optocoupler isolation, for better protection and resistance to interference.
For integration with PLC, the module can work with NPN type signals, provided there is a common ground wire.
Specifications:
Working voltage: 13.5V-30V
Input frequency range: 0-1 kHz
Output voltage range: 0-10V
Output adjustment: potentiometer for frequency-voltage calibration
Supported input pulse level: 5V, 12V, 24V without series resistor
Input isolation: optocoupler
Conversion response time: approximately 0.3-0.5 s
Common ground: yes, the module uses common ground for power, input and output
Connectors and functions:
| Connector | Role | Description |
|---|---|---|
| VCC | feeding | Working voltage input 13.5V-30V |
| GND | Food table | Module power supply board |
| F | Frequency input | Pulse signal input 0-1 kHz, supports 5V, 12V, 24V level |
| GND | Entrance table | Input signal ground |
| Vout | Voltage output | Proportional analog output 0-10V, adjustable from potentiometer |
| GND | Output table | Output signal ground |
Use:
Power the module at VCC and GND with a source between 13.5V and 30V.
Connect the pulse signal to terminal F and its ground to GND.
Reads the analog voltage on Vout relative to GND, in the range 0-10V.
Adjust the potentiometer to calibrate the relationship between frequency and output voltage until you get the desired correspondence.
For PLCs with NPN inputs, it is mandatory to provide a common ground wire between the equipment, the module requires a common ground.
If you are using an encoder, keep the rotation at a constant speed for at least 0.5 seconds for a stable measurement.
Precautions:
The input signal can be 5V, 12V or 24V and can be connected directly, but the frequency must be maintained for at least 0.5 seconds for stabilization.
The module has a response time of approximately 0.3-0.5 seconds, sudden frequency changes require time for the voltage to stabilize.
The input is optically isolated for anti-interference, but keep signal cables away from strong sources of electrical noise when possible.
All GNDs are common, use proper ground and firm connections for stable measurements.
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
