Product images are for informational purposes only and may vary slightly depending on the batch and supplier. Product specifications and prices may be subject to change without notice. We do our best to provide accurate and complete product specifications, but they may not be completely accurate. If you encounter any such situation, please let us know.
The product is intended for specialists and requires qualified and authorized personnel. The product does not include assembly/use instructions . Putting the product into operation by unqualified persons leads to the loss of the warranty according to the Terms and Conditions on the site.
The specified technical parameters (current, power, etc.) represent maximum allowable values under ideal operating conditions. For safe use and optimal lifespan, it is recommended to operate the product continuously at no more than 50% of the specified maximum values.
Non-latching push button, PBS-110, 7mm, NO, Black
Metal momentary push button for shortcuts in electronic projects and control panels, mounting in 7mm hole with included nut for secure fixing, 1NO Normally Open contact with 2 terminals, non-latching actuation for precise impulse, black finish and 7mm head, supports up to 250VAC 1A or 125VAC 3A.
Shipping by Thursday 22 October
Buying this product earns you 0.02 € in loyalty points.
International fast shipping within EU. Free Shipping for orders above 100 EUR in most EU countries.
We ship from our stock within 24H
You earn points with every order, worth 5%.
The PBS-110 non-latching metal push button is a push-type switch with automatic return to the initial position, intended for momentary controls in control panels, enclosures, and electronic equipment. The contact is normally open (NO), so the circuit closes only while the button is pressed. It is suitable for reset functions, momentary start, signaling, bells, test controls, and automation projects.
The button has a 1NO contact and two terminals and supports 250 VAC at 1 A or 125 VAC at 3 A. The button cap has a diameter of 7 mm, and mounting is done in a panel, in a 7 mm diameter hole.
Among the main features are the metal body with external thread, the black cap, the fixing nut included in the package, non-latching actuation, and the two terminals for solder connection or with connectors. The button does not require its own power supply, as it works as a simple contact in the controlled circuit.
As a dry contact, the button can be used as a digital input for Arduino, ESP32, STM32, Raspberry Pi, and other development boards, with an internal or external pull-up resistor, as well as in DC or AC control circuits, within the indicated voltage and current limits.
Specifications:
Supported voltage: 250 VAC at 1 A, 125 VAC at 3 A
Maximum current: 1 A at 250 VAC, 3 A at 125 VAC
Actuation: Non-latching (momentary)
Contact type: 1NO (normally open)
Terminals: 2
Button diameter: 7 mm
Mounting hole diameter: 7 mm
Mounting: Panel mount, with nut included
Color: Black
Use:
Drill a 7 mm diameter hole in the panel or enclosure, then insert the button through the hole from the outside.
Secure the button by tightening the nut from the package onto the threaded part, without excessive force, so as not to deform the body.
Connect the two terminals in series with the circuit you want to control; the terminals are equivalent, and the button has no polarity.
Do not exceed 250 VAC at 1 A or 125 VAC at 3 A.
If the button switches mains voltage, it is dangerous, and connections must be made only with the circuit disconnected from the mains, by a qualified person.
To use it as a digital input for Arduino, ESP32, STM32, or Raspberry Pi, connect one terminal to GND and the other to the input pin, then enable the internal pull-up resistor or use an external one.
Respect the voltage level accepted by the development board pin and do not apply voltages higher than those allowed to the input.
When soldering wires, keep the heating time of the terminals short, so as not to damage the button's plastic body.
For stable results in digital circuits, handle contact bounce (debounce) in software on press and release.
- Model
- PBS-110
Produs destinat utilizarii in proiecte electronice, automatizari, prototipare, educatie si cercetare.
Produsul trebuie utilizat numai conform specificatiilor tehnice mentionate in descriere si/sau in documentatia produsului.
Avertismente generale de siguranta:
Nu utilizati produsul la tensiuni, curenti sau temperaturi peste valorile specificate.
Montajul si conectarea trebuie realizate de persoane cu cunostinte tehnice minime in domeniul electric/electronic.
Evitati scurtcircuitele, inversarea polaritatii si conectarea gresita a alimentarii.
Nu lasati produsul alimentat nesupravegheat in timpul testelor.
Produsul nu este jucarie si nu este destinat copiilor.
Pentru modulele electronice, se recomanda utilizarea in carcase, panouri sau montaje protejate, dupa caz.
Identificare produs:
Denumirea produsului, codul/SKU-ul si caracteristicile tehnice sunt mentionate in pagina produsului si/sau pe eticheta ambalajului.
Producator / Importator / Distribuitor:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Website: www.sigmanortec.ro
Persoana responsabila in UE:
Sigmanortec S.R.L.
Calea Bucuresti nr. 9, Targu Jiu, Gorj, Romania
E-mail: [email protected]
Documentatie si siguranta:
Pentru informatii suplimentare, fise tehnice, declaratii de conformitate sau instructiuni, ne puteti contacta la [email protected].
